Regency F37-LPG Manuel D’Utilisation
F37 Regency
®
Rear Flued Room Sealed Freestanding Gas Heater
21
LATCH ADJUSTMENT
The door latch may require adjustment as the
door gasket material compresses after a few
fi res and after glass replacement. Turn the
handle on the adjustable catch to tighten or
loosen the latch.
door gasket material compresses after a few
fi res and after glass replacement. Turn the
handle on the adjustable catch to tighten or
loosen the latch.
GLASS REPLACEMENT
Your Regency
®
stove is supplied with high tem-
perature, 5 mm Neoceram ceramic glass that
will withstand the highest heat that your unit will
produce. In the event that you break your glass,
purchase your replacement from an authorized
Regency
will withstand the highest heat that your unit will
produce. In the event that you break your glass,
purchase your replacement from an authorized
Regency
®
dealer only, and follow the step-by-step
instructions for replacement.
Never operate your unit with broken
glass.
glass.
WARNING: Do not operate appli-
ance with the glass front removed,
cracked or broken. Replacement
of the glass should be done by a
licensed or qualifi ed service per-
son.
ance with the glass front removed,
cracked or broken. Replacement
of the glass should be done by a
licensed or qualifi ed service per-
son.
MITRED DOOR
Removing Glass:
Note: Wearing gloves will protect your
hands while handling glass.
1) Remove the door from the unit and place on
a soft surface to prevent scratching.
2) Pull out the door gasket.
3) Remove the 24 nuts holding the glass
retainers in place. Do not remove the nuts
underneath the retainers.
underneath the retainers.
4) Remove the door catch plate.
5) Remove glass retainers on sides fi rst (3 each
side) then remove two center retainers.
Note: Center glass retainers are glued to
center glass.
6) Remove glass from extrusions. When re-
moving center glass, leave white insulation
in place.
in place.
Installing Glass
1) Install both center and side glass onto
extrusions as per diagram.
2) Place glass assembly into door frame.
3) Install retainers by placing 1 drop of glue
where previously glued and put in place.
4) Install side retainers.
5) Install door catch plate.
6) Install the 24 nuts loosely, do not tighten
yet.
7) Tighten side panels nuts using the following
procedure:
a. tighten top & bottom outside corner
nuts (2)
b. tighten inside nuts (3)
c. tighten top & bottom inside corners
(2)
PANEL DOOR
1) Remove the door from the unit and place
on a soft surface to prevent scratching.
2) Pull out the door gasket.
3) Remove the nuts holding the glass retainers
in place.
4) Remove the glass retainers (sides, top and
bottom) and the door catch plate.
5) Replace the glass. The glass must have
gasketing around it.
6) Reverse the previous steps, replace the
retainers and fasten with the nuts but do
not overtighten, as this can break the glass.
Note: the door catch plate fi ts on top of the
left side retainer.
not overtighten, as this can break the glass.
Note: the door catch plate fi ts on top of the
left side retainer.
7) Put gasket glue on the retainers, but do not
put glue on the screws. Replace the door
gasket, the two ends butt tight together on
the bottom edge of the door.
gasket, the two ends butt tight together on
the bottom edge of the door.
8) Replace door on the stove and check the
seal.
8) Tighten the 10 nuts on center glass re-
tainer.
9) Repeat step 7 for other side panel.
10) Replace new gasket by gluing it in place.
11) Install door onto stove and check the
seal.
MAINTENANCE