Regency C33-LP2 Manuel D’Utilisation
10
Regency CLASSIC C33-2 Freestanding Gas Stove
HIGH ELEVATION
This unit is approved in Canada for altitude 0 to
4500 ft. (CAN1 2.17-M90) with the orifice sup-
plied.
4500 ft. (CAN1 2.17-M90) with the orifice sup-
plied.
GAS PIPE
PRESSURE TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig. (3.45
kPa). Disconnect piping from valve at pres-
sures over 1/2 psig (14" w.c.).
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig. (3.45
kPa). Disconnect piping from valve at pres-
sures over 1/2 psig (14" w.c.).
The manifold pressure is controlled by a reg-
ulator built into the gas control, and should be
checked at the pressure test point.
ulator built into the gas control, and should be
checked at the pressure test point.
Note: To properly check gas pressure,
both inlet and manifold pressures
should be checked using the valve
pressure ports on the valve.
should be checked using the valve
pressure ports on the valve.
1) Make sure the valve is in the "OFF" position.
2) Loosen the "IN" and/or "OUT" pressure
tap(s), turning counterclockwise with a
1/8" wide flat screwdriver.
1/8" wide flat screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON"
position.
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
be within the limits specified on the safety
label.
6) When finished reading manometer, turn off
the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8"
flat screwdriver. Screw should be snug,
but do not over tighten.
tighten the screw (clockwise) with a 1/8"
flat screwdriver. Screw should be snug,
but do not over tighten.
GAS CONNECTION
The gas connection is a 3/8" NPT rigid pipe. The
gas line can be rigid pipe or to make installation
easier, use a listed flexible connector and/or
copper pipe if allowed by local codes. For
minimum and maximum supply pressure see
the System Data table below.
gas line can be rigid pipe or to make installation
easier, use a listed flexible connector and/or
copper pipe if allowed by local codes. For
minimum and maximum supply pressure see
the System Data table below.
Note: During any pressure testing of
the gas supply piping system that
exceeds test pressures of 1/2
psig, this appliance and its indi-
vidual shut-off valve must be dis-
connected from the piping sys-
tem. If test pressures equal to or
less than 1/2 psig are used then
this appliance must be isolated
from the piping system by clos-
ing its individual manual shut-off
valve during the testing.
exceeds test pressures of 1/2
psig, this appliance and its indi-
vidual shut-off valve must be dis-
connected from the piping sys-
tem. If test pressures equal to or
less than 1/2 psig are used then
this appliance must be isolated
from the piping system by clos-
ing its individual manual shut-off
valve during the testing.
Output capacity:
The efficiency rating of the appliance is a
product thermal efficiency rating determined
under continuous operating conditions and
was determined independently of any installed
system.
The efficiency rating of the appliance is a
product thermal efficiency rating determined
under continuous operating conditions and
was determined independently of any installed
system.
INSTALLATION
Installing into Existing
Woodstove Flue System
1) Clean existing chimney system.
2) Install stove pipe adapter
3) Install any reducers that may be needed to
fit 6" flue pipe adapter.
4) Run 4" flex liner into existing chimney.
5) Slip liner through 6" flue pipe and hook up
to flue collar with screws.
Note: For ease of instal-
lation, use a slip
section when in-
s t a l l i n g
with a ver-
tical flue
pipe.
section when in-
s t a l l i n g
with a ver-
tical flue
pipe.
SYSTEM DATA
(For 0 to 2,000 feet altitude)
Orifice Sizes:
Burner
Natural Gas
#36
Burner
Propane
#52
Max. Input Rating
Natural Gas
33,000 Btu/h
Propane
33,000 Btu/h
Min. Input Rating
Natural Gas
17,000 Btu/h
Propane
17,000 Btu/h
Output Capacity with blower Off
Natural Gas
23,200 Btu/h
Propane
23,100 Btu/h
Output Capacity with blower On
Natural Gas
24,600 Btu/h
Propane
24,420 Btu/h
Supply Pressure
Natural Gas
min.
5.0" w.c
max.
8.0" w.c.
Propane
min.
12.0" w.c.
max.
13.0" w.c.
Manifold Pressure High
Natural Gas
3.8" +/- 0.2" w.c.
Propane
11" +/- 0.2" w.c.
Manifold Pressure Low
Natural Gas
1.1" +/- 0.2" w.c.
Propane
2.9" +/- 0.2" w.c.
Electrical: 120V, 1.13A, 60 Hz.
Circulation Fan: (optional) 2 speed
Circulation Fan: (optional) 2 speed
75/125 CFM.
Log Set: Ceramic fiber, 4 per set.
SYSTEM DATA
(For 2,000 to 4,500 feet altitude)
Orifice Sizes:
Burner
Natural Gas
#38
Max. Input Rating
Natural Gas
29,000 Btu/h
Min. Input Rating
Natural Gas
15,300 Btu/h
Output Capacity with blower Off
Natural Gas
20,400 Btu/h
Output Capacity with blower On
Natural Gas
21,600 Btu/h