Regency C33-LP2 Manuel D’Utilisation

14

Regency CLASSIC C33-2 Freestanding Gas Stove

1) Turn burner OFF using "ON/OFF" switch.

2) Turn gas control knob so indicator points to

"OFF" position and allow 5 minutes for any
gas in the combustion chamber to escape.

3) Turn gas control knob counterclockwise so

indicator points to the "PILOT" position.
Depress the gas control knob fully. De-
press the igniter button several times until
the pilot lights. After approximately one
minute, release the gas control knob. The
pilot flame should continue to burn. If the
pilot does not remain lit, repeat operation
allowing a longer period before releasing
gas control knob.

4) When the pilot stays lit, turn the gas knob

further counterclockwise to the "ON" posi-
tion.

5) Use the ON/OFF switch, wall switch, ther-

mostat or remote control to turn on the unit.

6) Rotate the flame height regulator (Hi/Lo) to

adjust the flame height higher or lower.

1) Use the "ON/OFF" switch, wall switch,

thermostat or remote control to turn off the
burner.

2) Push in the PILOT knob slightly and turn

clockwise to "OFF". Do not force.

3) Turn off all electric power to the appliance

if service is to be performed.

1) The FIRST FIRE in your stove is part of the

paint curing process. To ensure that the
paint is properly cured, it is recommended
that you burn your fireplace for at least four
(4) hours the first time you use it with the
fan on. When first operated, the unit will
release an odour caused by the curing of
the paint and the burning off of any oils
remaining from manufacturing. Smoke de-
tectors in the house may go off at this time.
Open a few windows to ventilate the room
for a couple of hours. The glass panel may
require cleaning.

2) Read and understand these instructions

before operating this appliance.

3) Check to see that all wiring is correct and

enclosed to prevent possible shock.

4) Check to ensure there are no gas leaks.

5) Make sure the glass in the door frame is

properly positioned. Never operate the
appliance with the glass removed.

6) Verify that the venting is unobstructed.

7) Verify log placement. If the pilot cannot be

seen when lighting the unit - the logs have
been incorrectly positioned.

8) The unit should never be turned off, and on

again without a minimum of a 60 second
wait for purging.

1) Always turn off the gas valve before

cleaning. For relighting, refer to lighting
instructions. Keep the burner and control
compartment clean by brushing and vacu-
uming at least once a year.

When cleaning the logs, use a soft clean
brush as the logs are fragile and easily
damaged.

2) Clean appliance and door with a damp cloth

(never when unit is hot).  Never use an
abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner
(when it starts to cloud up).

3) The heater is finished in a heat resistant

paint and should only be refinished with
heat resistant paint. Regency uses Stove
Brite Paint - Metallic Black #6309.

4) Make a  periodic check of burner for proper

position and condition. Visually check the
flame of the burner periodically, making
sure the flames are steady; not lifting or
floating. If there is a problem, call a qualified
service person.

5) The appliance and venting system must be

inspected before use, and at least annual-
ly, by a qualified field service person, to
ensure that the flow of combustion and
ventilation air is not obstructed.

During the annual service call, the burners
should be removed from the burner tray
and cleaned. Replace the embers and rock
wool.

6) Each time the appliance is lit, it may cause

condensation and fog the glass.  This
condensation is normal and will disappear
in a few minutes as the glass heats up.

7) Caution: Label all wires prior to disconnec-

tion when servicing controls. Wiring errors
can cause improper and dangerous oper-
ation.  Verify proper operation after serv-
icing.