Nilfisk-Advance America 5200B Manuel D’Utilisation

14

Terra™ 5200B – 146 1996 000(2)2004-08

14. Reassemble all the components of the filter in the 

reverse order of disassembly.

15. If necessary, clean the filter compartment rubber seal 

(3, Fig. AB) along its perimeter and check its integrity. 
If necessary, replace it.

16. Reassemble all the components in the reverse order 

of disassembly.

Side skirt
1.

Drive the machine on a level ground that is suitable 
for checking the skirt height.

2.

Engage the parking brake by means of the pedal and 
the lever (26 and 19, Fig. B).

3.

Turn the ignition switch (18, Fig. B) to “0” position.

4.

Disengage the retainers (8 and 6) and open the right 
and left doors (7 and 5, Fig. C).

5.

Check the side skirt (2, Fig. F) integrity.
Replace the skirts when they have cuts (1, Fig. Q) 
larger than 0.79 in (20 mm) or cracks/tears (2) larger 
than 0.39 in (10 mm) (for skirt replacement, refer to 
the Service Manual).

6.

Check that side skirt (2, Fig. F) height from ground is 
within 0 – 0.12 in (0 – 3 mm) (Fig. R).
After loosening the screws (3, Fig. F), if necessary, 
adjust the skirt position. Then tighten the screws (3).

Front and rear skirt
7.

Remove the main broom, as described in the related 
paragraph.

8.

Check the front and rear skirts (1 and 2, Fig. W) for 
integrity.
Replace the skirts when they have cuts (1, Fig. Q) 
larger than 0.79 in (20 mm) or cracks/tears (2) larger 
than 0.39 in (10 mm) (for skirt replacement, refer to 
the Service Manual).

9.

Check that the front and rear skirts (1 and 2, Fig. W) 
rub lightly on the floor but are not completely lifted 
from the ground (see figure S).
After loosening the screws (3, Fig. W), if necessary, 
adjust the skirt position. Then tighten the screws (3).

10. Press the front (25, Fig. B) skirt lifting pedal 

completely, and check that the front skirt lifts 1.97 in 
(50 mm) approximately.
Release the pedal and check that the skirt returns to 
the initial position and not in an intermediate position. 
If necessary, adjust the skirt lifting cable (1, Fig. X) by 
using the adjuster (2) on the left front side of the skirt 
(for the front skirt control cable replacement, refer to 
the Service Manual).

11. Reassemble all the components in the reverse order 

of disassembly.

1.

Engage the parking brake by means of the pedal and 
the lever (26 and 19, Fig. B).

2.

Open the hood (1, Fig. V) and hold it by using the 
related rod (16, Fig. V).

3.

Check that the hydraulic oil level in the tank (14, Fig. 
V) is between the MIN and MAX indicators (as shown 
in Fig. Y).

4.

If necessary add hydraulic oil - viscosity grade 32 cSt 
- through the plug (1, Fig. Y).

5.

Disengage to lock rod (16, Fig. V) and close the hood 
(1, Fig. V).

1.

Drive the machine on a level ground and engage the 
parking brake by means of the pedal and the lever (26 
and 19, Fig. B).

2.

Turn the ignition switch (18, Fig. B) to “0” position.

3.

Open the hood (13, Fig. C) and hold it by using the 
related rod (16, Fig. V).

4.

Check the correct level of electrolyte inside the 
batteries; if necessary, top up through the caps (3, 
Fig. V).
Leave the caps (3) open for the next recharging.
Clean, if necessary, the upper surface of the 
batteries.

5.

Check that the battery charger is appropriate, 
referring to the Battery Charger Operating Manual.
The battery charger voltage rating is 24 V.
The battery charger must be appropriate for the 
battery installed on the machine.