ONKYO TXNR828 Manuel D’Utilisation
Advanced Operations
En-80
12V Trigger Out
When Zone 2 is turned on, the output from the
ZONE 2 12V TRIGGER OUT jack goes high (+12 V
and max. 150 mA for Zone 2). Connecting this jack to
a 12-volt trigger input on a component in Zone 2 will
make that component turn on or off as the AV
receiver turns on or off the Zone 2.
ZONE 2 12V TRIGGER OUT jack goes high (+12 V
and max. 150 mA for Zone 2). Connecting this jack to
a 12-volt trigger input on a component in Zone 2 will
make that component turn on or off as the AV
receiver turns on or off the Zone 2.
■
Operating on the AV receiver
Tip
• The Whole House Mode function shares the input source of
main room with Multi Zone (
).
■
Operating on the remote controller
To control Zone 2/3, you must press ZONE on the
remote controller first.
ZONE turns red when Zone 2 is on, and green when
Zone 3 is on.
remote controller first.
ZONE turns red when Zone 2 is on, and green when
Zone 3 is on.
Adjusting the Volume for Zone 2
■
Operating on the remote controller
■
Operating on the AV receiver
If your Zone 2 speakers are connected to a receiver
or integrated amplifier in Zone 2, use its volume
control to adjust the volume.
or integrated amplifier in Zone 2, use its volume
control to adjust the volume.
Controlling Multi Zone Components
ZONE 2 ZONE 3
MASTER VOLUME
8ON/STANDBY
Input selector buttons
1
To turn on Zone 2/3 and select an input source,
press ZONE 2 or ZONE 3 followed by an input
selector button within 8 seconds.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
press ZONE 2 or ZONE 3 followed by an input
selector button within 8 seconds.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
Tip
• The Zone 2 trigger output goes high (+12 V).
To select AM or FM, press ZONE 2 or ZONE 3
and the TUNER input selector repeatedly.
and the TUNER input selector repeatedly.
To select the same source as the main room’s,
press ZONE 2 or ZONE 3 twice. “Zone 2
Selector: Source” or “Zone 3 Selector: Source”
appears on the AV receiver’s display.
press ZONE 2 or ZONE 3 twice. “Zone 2
Selector: Source” or “Zone 3 Selector: Source”
appears on the AV receiver’s display.
2
To turn off Zone 2/3, press ZONE 2 or ZONE 3
followed by
followed by
8ON/STANDBY within 8 seconds.
The zone is turned off.
Tip
• The Zone 2 trigger output goes low (0 volts).
8RECEIVER
MUTING
VOL
q/w
ZONE
Input selector buttons
1
Press ZONE repeatedly, then point the remote
controller at the AV receiver and press
8RECEIVER.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
controller at the AV receiver and press
8RECEIVER.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
Tip
• The Zone 2 trigger output goes high (+12 V).
2
To select an input source for Zone 2/3, press
ZONE repeatedly, followed by an INPUT
SELECTOR button.
To select AM or FM, press ZONE and the TUNER
input selector repeatedly.
ZONE repeatedly, followed by an INPUT
SELECTOR button.
To select AM or FM, press ZONE and the TUNER
input selector repeatedly.
3
To turn off Zone 2/3, press ZONE repeatedly,
followed by
followed by
8RECEIVER.
The zone is turned off.
Tip
• The Zone 2 trigger output goes low (0 volts).
1
Press ZONE repeatedly to select Zone 2.
2
Use VOL
q/w.
1
Press ZONE 2 (the Z2 indicator on the AV
receiver’s display flashes).
receiver’s display flashes).
2
Use MASTER VOLUME control within 8
seconds.
seconds.