Sharp XLDH259P Manuel D’Utilisation
E-11
To scan the preset stations
Q
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
automatically. (Preset memory scan)
Press the PRESET (
1
or ) button for more than
0.5 seconds. The preset number will fl ash and the
programed stations will be tuned in sequentially, for 5
seconds each.
Press the PRESET (
programed stations will be tuned in sequentially, for 5
seconds each.
Press the PRESET (
2
or ) button again when the
desired station is located.
To erase entire preset memory
Q
Press the POWER ON/STAND-BY button to enter the stand-by
1
mode.
While pressing down the FUNCTION button, press the POWER
While pressing down the FUNCTION button, press the POWER
2
ON/STAND-BY button until “TUNER CLEAR” appears.
Setting the clock (Remote control only)
In this example, the clock is set for the 12-hour (AM 12:00) display.
Press the ON/STAND-BY button to turn the power on.
1
Press the CLOCK/TIMER button.
2
Within 10 seconds, press the MEMORY button. Press
3
the
or
button to select 12-hour or 24-hour display
and then press the MEMORY button.
To recall a preset station
Q
Press the PRESET (
1
or ) button for less than 0.5
seconds to select the desired station.
Within 30 seconds, press the MEMORY button to store
4
that station in memory. If the “MEMORY” and preset
number indicators disappear before the station is
memorized, repeat the operation from step 2.
Repeat steps 1 - 4 to set other stations, or to change
number indicators disappear before the station is
memorized, repeat the operation from step 2.
Repeat steps 1 - 4 to set other stations, or to change
5
a preset station. When a new station is stored in the
memory, the station previously memorized for that
preset channel number will be erased.
memory, the station previously memorized for that
preset channel number will be erased.
Note:
The backup function protects the memorized stations for a few
hours should there be a power failure or the AC power cord
become disconnected.
The backup function protects the memorized stations for a few
hours should there be a power failure or the AC power cord
become disconnected.
Listening to the radio
Tuning
Q
Press the ON/STAND-BY button to turn the power on.
1
Press the FUNCTION button on the main unit
2
or TUNER (BAND) button on the remote control
repeatedly to select the desired frequency band (FM
stereo, FM mono or AM).
Press the TUNING (
repeatedly to select the desired frequency band (FM
stereo, FM mono or AM).
Press the TUNING (
3
or ) (TUNING (
or
))
button to tune in to the desired station.
Manual tuning:
O
Press the TUNING ( or ) (TUNING (
or
))
button repeatedly to tune in to the desired station.
Auto tuning:
Auto tuning:
O
When the TUNING ( or ) (TUNING (
or
))
button is pressed for more than 0.5 seconds, scanning
will start automatically and the tuner will stop at the fi rst
receivable broadcast station.
will start automatically and the tuner will stop at the fi rst
receivable broadcast station.
Notes:
When radio interference occurs, auto scan tuning may
O
stop automatically at that point.
Auto scan tuning will skip weak signal stations.
Auto scan tuning will skip weak signal stations.
O
To stop the auto tuning, press the TUNING (
O
or )
(TUNING (
or
)) button again.
To receive an FM stereo transmission:
Press the FUNCTION button on main unit or TUNER (BAND)
O
button on the remote control to select stereo mode and “ST”
indicator will be displayed. “
indicator will be displayed. “
” will appear when an FM
broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button
If the FM reception is weak, press the TUNER (BAND) button
O
to extinguish the “ST” indicator. The reception changes to
monaural, and the sound becomes clearer.
monaural, and the sound becomes clearer.
Presetting a station
Q
You can store 40 AM and FM stations in memory and
recall them at the push of a button. (Preset tuning)
recall them at the push of a button. (Preset tuning)
Perform steps 1 - 3 in “Tuning”.
1
Press the MEMORY button.
2
Within 30 seconds, press the PRESET (
3
or ) button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
in memory, in order, starting with preset channel 1.
The 24-hour display will appear.
(0:00 - 23:59)
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
(AM 0:00 - PM 11:59)
To adjust the hour, press the
4
or
button and then
press the MEMORY button. Press the
or
button
once to advance the time by 1 hour. Hold it down to
advance continuously.
advance continuously.
XL-DH259P_USA_EN.indd 11
XL-DH259P_USA_EN.indd 11
12/29/2010 4:53:06 PM
12/29/2010 4:53:06 PM