Sharp XLDH259P Manuel D’Utilisation
E-13
Headphones
Q
Do not turn the volume on to full at switch on and listen
O
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
Before plugging in or unplugging the headphone,
from earphones and headphones can cause hearing
loss.
Before plugging in or unplugging the headphone,
O
reduce the volume.
Be sure your headphone has a 1/8" (3.5 mm) diameter
Be sure your headphone has a 1/8" (3.5 mm) diameter
O
plug and impedance between 16 and 50 ohms. The
recommended impedance is 32 ohms.
Plugging in the headphone disconnects the speakers
recommended impedance is 32 ohms.
Plugging in the headphone disconnects the speakers
O
automatically. Adjust the volume using the VOLUME
control.
control.
Enhancing your system
The connection cord is not included. Purchase a commercially
available cord as shown below.
available cord as shown below.
M I C R O C O M P O N E N T S Y S T E M
XL-DH259P
Portable
audio
player, etc.
audio
player, etc.
Audio cable
(not supplied)
(not supplied)
Listening to the playback sounds of
Q
portable audio player, etc.
Use a connection cord to connect the portable audio
1
player etc. to the AUDIO IN jack. When using video
equipment, connect the audio output to this unit and
the video output to a television.
Press the ON/STAND-BY button to turn the power on.
equipment, connect the audio output to this unit and
the video output to a television.
Press the ON/STAND-BY button to turn the power on.
2
Press the AUDIO IN button on the remote control or
3
FUNCTION button repeatedly on main unit to select
AUDIO IN function.
Play the connected equipment. If volume level of the
AUDIO IN function.
Play the connected equipment. If volume level of the
4
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
Note:
To prevent noise interference, place the unit away from the
television.
To prevent noise interference, place the unit away from the
television.
Timer and sleep operation
(Remote control only) (continued)
(Remote control only) (continued)
Desired time
90 minutes
Sleep operation will
automatically stop
automatically stop
Timer playback start
time
time
Sleep operation
Q
The radio, compact disc, iPod and USB can all be turned
off automatically.
off automatically.
Play back the desired sound source.
1
Press the SLEEP button.
2
Within 10 seconds, press the SLEEP button repeatedly
3
to select the time.
10
20
30 .......
80
90
“SLEEP” will appear.
4
The unit will enter the power stand-by mode
5
automatically after the preset time has elapsed. The
volume will be turned down 1 minute before the sleep
operation fi nishes.
volume will be turned down 1 minute before the sleep
operation fi nishes.
To confi rm the remaining sleep time:
While “SLEEP” is indicated, press the SLEEP button.
1
To cancel the sleep operation:
Press the ON/STAND-BY button while “SLEEP” is
indicated. To cancel the sleep operation without setting
the unit to the stand-by mode, proceed as follows.
indicated. To cancel the sleep operation without setting
the unit to the stand-by mode, proceed as follows.
While “SLEEP” is indicated, press the SLEEP button.
1
Within 10 seconds, press the SLEEP button repeatedly
2
to select “SLEEP 00”.
Sleep timer setting
Timer playback setting
End time
To use timer and sleep operation together
Q
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
Set the sleep time (see above, steps 1 - 5).
1
While the sleep timer is set, set the timer playback
2
(steps 2 - 9, page 12).
XL-DH259P_USA_EN.indd 13
XL-DH259P_USA_EN.indd 13
12/29/2010 4:53:06 PM
12/29/2010 4:53:06 PM