ONKYO HT-RC180 Manuel D’Utilisation
117
There are two ways you can connect Zone 3 speakers:
1. Connect them directly to the AV receiver.
2. Connect them to an amp in Zone 3.
1. Connect them directly to the AV receiver.
2. Connect them to an amp in Zone 3.
Connecting Your Zone 3 Speakers Directly
to the AV receiver
to the AV receiver
This setup allows 3.1-channel playback in your main
room and 2-channel stereo playback in Zone 3, with a
different source in each room. This is called Powered
Zone 3, as the Zone 3 speakers are powered by the AV
receiver.
room and 2-channel stereo playback in Zone 3, with a
different source in each room. This is called Powered
Zone 3, as the Zone 3 speakers are powered by the AV
receiver.
Hookup
• Connect your Zone 3 speakers to the AV receiver’s
• Connect your Zone 3 speakers to the AV receiver’s
SURR/ZONE 3 L/R speaker terminals.
Notes:
• With this setup, the Zone 3 volume is controlled by the
• With this setup, the Zone 3 volume is controlled by the
AV receiver.
• Powered Zone3 cannot be used if “Speaker Type
(Front)” is set to “Bi-Amp” (see page 51).
Connecting Your Zone 3 Speakers to an
Amp in Zone 3
Amp in Zone 3
This setup allows 7.1-channel playback in your main lis-
tening room and 2-channel stereo playback in Zone 3,
with a different source in each room.
tening room and 2-channel stereo playback in Zone 3,
with a different source in each room.
Hookup
• Use an RCA audio cable to connect the AV receiver’s
• Use an RCA audio cable to connect the AV receiver’s
ZONE 3 PRE OUT L/R jacks to an analog audio input
on your Zone 3 amp.
on your Zone 3 amp.
• Connect your Zone 3 speakers to the speaker terminals
on your Zone 3 amp.
Note:
With the default settings, the Zone 3 volume must be set
on the Zone 3 amp. If your Zone 3 amp has no volume
control, set the “Zone3 Out” setting to “Variable” so that
you can set the Zone 3 volume on the AV receiver (see
page 119).
With the default settings, the Zone 3 volume must be set
on the Zone 3 amp. If your Zone 3 amp has no volume
control, set the “Zone3 Out” setting to “Variable” so that
you can set the Zone 3 volume on the AV receiver (see
page 119).
Zone 3 12V Trigger (TX-NR807)
When Zone 3 is turned on, the output from the 12V
TRIGGER OUT ZONE 3 goes high (+12 volts, 25 mil-
liamperes max). Connecting this jack to a 12-volt trigger
input on a component in Zone 3 will make that compo-
nent turn on or off as and when Zone 3 is turned on or off
on the AV receiver.
TRIGGER OUT ZONE 3 goes high (+12 volts, 25 mil-
liamperes max). Connecting this jack to a 12-volt trigger
input on a component in Zone 3 will make that compo-
nent turn on or off as and when Zone 3 is turned on or off
on the AV receiver.
Connecting Zone 3
To use this setup, you must set the “Powered Zone2”
and “Powered Zone3” setting to “Act” (see page 118).
and “Powered Zone3” setting to “Act” (see page 118).
L
R
Main room
Zone 3
TV
AV receiver
R
L
IN
Main room
TV
Zone 3
AV receiver
Receiver/
integrated amp
TX-NR807_En.book Page 117 Tuesday, July 28, 2009 12:00 PM