ONKYO HT-RC180 Manuel D’Utilisation
119
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
■ Zone2/3 Out
If you’ve connected your Zone 2/3 speakers to an amp
with no volume control, set the “Zone2 Out” and “Zone3
Out” setting, respectively, to “Variable” so that you can
set the volume, balance, and tone of zone 2 and volume
and balance of zone 3 on the AV receiver.
If you’ve connected your Zone 2/3 speakers to an amp
with no volume control, set the “Zone2 Out” and “Zone3
Out” setting, respectively, to “Variable” so that you can
set the volume, balance, and tone of zone 2 and volume
and balance of zone 3 on the AV receiver.
■ Zone2/3 Maximum Volume
With this setting, you can limit the maximum volume for
Zone 2/3. When the “Volume Display” setting is set to
“Absolute”, the “Maximum Volume” range is “Off”, 99
to 50. When it’s set to “Relative”, the range is “Off”,
+17 dB to –32 dB. To disable this setting, select “Off”.
With this setting, you can limit the maximum volume for
Zone 2/3. When the “Volume Display” setting is set to
“Absolute”, the “Maximum Volume” range is “Off”, 99
to 50. When it’s set to “Relative”, the range is “Off”,
+17 dB to –32 dB. To disable this setting, select “Off”.
■ Zone2/3 Power On Volume
This setting determines what the volume will be for
Zone 2/3 each time the AV receiver is turned on.
When the “Volume Display” preference is set to “Abso-
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
This setting determines what the volume will be for
Zone 2/3 each time the AV receiver is turned on.
When the “Volume Display” preference is set to “Abso-
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
Q dB, –81 dB to
+18 dB.
To use the same volume level as when the AV receiver
was last turned off, select “Last”.
The “Zone2/3 Power On Volume” cannot be set higher
than the “Zone2/3 Maximum Volume” setting.
To use the same volume level as when the AV receiver
was last turned off, select “Last”.
The “Zone2/3 Power On Volume” cannot be set higher
than the “Zone2/3 Maximum Volume” setting.
Setting the Multi Zone
1
Press the [RECEIVER] button
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q]/[w]
buttons to select “7. Hardware
Setup”, and then press [ENTER].
The “Hardware Setup” menu appears.
Setup”, and then press [ENTER].
The “Hardware Setup” menu appears.
3
Use the Up and Down [
q]/[w]
buttons to select “2. Multi Zone”,
and then press [ENTER].
The “Multi Zone” menu appears.
and then press [ENTER].
The “Multi Zone” menu appears.
4
Use the Up and Down [
q]/[w]
buttons to select an item, and
use the Left and Right [
use the Left and Right [
e]/[r]
buttons to change it.
The items are explained below.
The items are explained below.
5
When you’ve finished, press the
[SETUP] button.
The setup menu closes.
[SETUP] button.
The setup menu closes.
7. Hardware
Setup
1. Remote
ID
2. Multi
Zone
3. Tuner
4. HDMI
5. Network
6. Firmware
4. HDMI
5. Network
6. Firmware
Update
Fixed: The Zone 2/3 volume must be set on the
amp in that zone.
Variable: The Zone 2/3 volume can be set on the AV
receiver.
TX-NR807_En.book Page 119 Tuesday, July 28, 2009 12:00 PM