Marshall electronic V-R65P-HD Manuel D’Utilisation

V-R65P-HD

Users Guide

Marshall Electronics

Optional Accessories (continued)

Replacement
Protection Screen

V-R65-RPS

Use to replace damaged or scratched protective
cover for screen

Rack-mount kit A

V-R65-1M

(Image not available)

Single monitor mount for 19” rack

Rack-mount kit B

V-R65-2M

(Image not available)

Dual monitor mount for 19” rack

Component input cable

RGB-5HD15-X

HD-15 to BNC break out cable
(X = Length in feet 6, 10, 15, 20)

Power Adapter Cable

V-PAC-D

Use with Anton Bauer D-type connection

Power Adapter Cable

V-PAC-XLR

Use with 4 Pin XLR connections

Mount for IDX Batteries

V-R65-BA

Attaches to V-R65P-HD monitor

Sequential 2 channel
charger

IDX-VL-2Plus

2-channel sequential charger with a built-in 60W power sup-
ply. Charges 2 ENDURA E series batteries in fewer than 5
hours. One 10’ XLR cable included.only 2 lbs

Sequential 4 channel
charger

IDX-VL-4

Economically charges 4 ENDURA E series batteries in under
6 hours using Full Power Charge (FPC) method

Simultaneous 4 channel
charger

IDX-VL-4S

Charges 4 ENDURA E series batteries in 2.5 hours or less

55 W Lithium Battery

IDX-E50S

V-Mount battery pack with 3 LED power Indicator

55 W Lithium Battery
with Power Link

IDX-E50

V-Mount Battery Pack with PowerLink includes accurate
Power Status Display and supports Digi-View

82 W Lithium Battery

IDX-E80S

V-Mount battery pack with 3 LED power Indicator

82 W Lithium Battery
with Power Link

IDX-E80

V-Mount Battery Pack with PowerLink includes accurate
Power Status Display and supports Digi-View

1. Unpack the V-R65P-HD and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may
  have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-
  6608. If you are not located within the continental united states call +1 310-333-0606.

2. Connect required cables for signal input and output.
Please note that power must be applied to the V-R65P-HD for the HDSDI/SDI and composite outputs to be
activated. All BNC connectors should be rated for 75

3. Plug the V-PS12-5V-1 power supply into the A.C. source
  Please note that power can be supplied from a variety of DC sources, such as batteries or Vehicle power.
  Input power range is 10.7 to 15 Volt D.C. In operation, the V-R65P-HD will draw approx. 0.8 amp.
  Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.

4. Turn on the V-R65P-HD by depressing the power switch located on the front of the unit.

Operational Setup

* Tally lamps active when connected to ground

HDSDI or SDI in.

270Mbs to 1.5Gbs

Automatically

terminates to 75Ω

Refer to Table 3
for signal types

Composite Video IN

NTSC/PAL

Automatically

terminates

to 75Ω

Component Video

or VGA INPUT

HD-15 Female refer

to Table 1 for signal

pin outs and Table 2

for Signal Types

Re-Clocked

HDSDI/SDI Output.

Signal in equals

signal out

Active

Composite

Output

Pin1- Green
Pin2- Red
Pin3-Amber
Pin4 Gnd -
Pin5-
Pin6-
Pin7-

Pin8-
Pin 9-
Pin10-
Pin11-
Pin12-
Pin13-
Pin14-
Pin15-

Tally IN DB-15 Female

10.7 to 15 VDC

V-PS12-5V-1 power supply is

included

Left Pin - Pos. Right Pin- Neg

Input Connectors