Scag Power Equipment SWZV Manuel D’Utilisation
Section 6
24
Figure 6-5 Cutter Deck Height Adjustment
2. Rotate the cutter blade on the left side of the cutter
deck. Position the cutter blade so it is facing "front to
back" on the machine.
back" on the machine.
3. Check the measurement from the floor to the cutter
blade tip at the rear of the left side blade. If the
measurement is not at 3", an adjustment can be made
using the deck height control rod.
measurement is not at 3", an adjustment can be made
using the deck height control rod.
4. Adjust by loosening the jam nuts on the deck height
control rod. Turn the deck height control rod until the
3" setting is acheived. Hold the deck height control
rod and tighten the jam nuts.
3" setting is acheived. Hold the deck height control
rod and tighten the jam nuts.
5. Once the adjustment is made to the deck height
control rod, Check the measurement from the floor to
the cutter blade tip at the front of the left side blade.
If the measurement is not at 3", an adjustment must
be made using the cutter deck adjustment lever.
Adjust as follows:
the cutter blade tip at the front of the left side blade.
If the measurement is not at 3", an adjustment must
be made using the cutter deck adjustment lever.
Adjust as follows:
A. Loosen the elastic stop nuts securing the deck
level links on front of the cutter deck on both
sides (See Figure 6-3, Page 24 and Figure 6-4,
Page 25 for Cutter Deck Adjustment Lever
Location).
sides (See Figure 6-3, Page 24 and Figure 6-4,
Page 25 for Cutter Deck Adjustment Lever
Location).
DECK HEIGHT
CONTROL ROD
LOOSEN HERE
WARNING:
Always wear proper hand and eye protection when
working with cutter blades.
working with cutter blades.
B. Turn the adjustment bolts on both side either
clockwise to raise or counterclockwise to lower
the front of the cutter deck until the
measurements are equal. Tighten the elastic stop
nuts.
the front of the cutter deck until the
measurements are equal. Tighten the elastic stop
nuts.
6. Rotate the cutter blade on the right side of the cutter
deck. Position the cutter blade so it is facing "front to
back" on the machine.
back" on the machine.
7. Check the measurement from the floor to the cutter
blade tip at the front and rear of the right side blade.
If the measurement is not at 3", an adjustment must
be made using the cutter deck adjustment lever.
Adjust as follows:
If the measurement is not at 3", an adjustment must
be made using the cutter deck adjustment lever.
Adjust as follows:
A. Loosen the elastic stop nuts securing the deck
level links on front of the cutter deck on both
sides (See Figure 6-3 and Figure 6-4 for Cutter
Deck Adjustment Lever Location).
sides (See Figure 6-3 and Figure 6-4 for Cutter
Deck Adjustment Lever Location).
B. Turn the adjustment bolts on both side either
clockwise to raise or counterclockwise to lower
the cutter deck until the measurements are equal.
Tighten the elastic stop nuts.
the cutter deck until the measurements are equal.
Tighten the elastic stop nuts.
Custom-Cut Baffle Adjustment
The Custom-Cut Baffle is designed to deliver optimum
airflow and superior cutting performance in any type of
grass. The Custom-Cut Baffle can be raised or lowered
to precisely tailor the deck's performance for the type of
grass being cut. Your machine will be equipped with
either a three (3) position or seven (7) position Custom-
Cut Baffle. Before making adjustments to the location of
the Custom-Cut Baffle, determine which version your
machine is equipped with. Reference the following page
when making adjustments.
airflow and superior cutting performance in any type of
grass. The Custom-Cut Baffle can be raised or lowered
to precisely tailor the deck's performance for the type of
grass being cut. Your machine will be equipped with
either a three (3) position or seven (7) position Custom-
Cut Baffle. Before making adjustments to the location of
the Custom-Cut Baffle, determine which version your
machine is equipped with. Reference the following page
when making adjustments.