Korg Triton Studio Manuel D’Utilisation

The “LFO1 Intensity,” “JS+Y (LFO1 JS+Y Int.)” and “AMS 
(LFO1 AMS)” settings will be added to determine the depth 
and direction of the pitch modulation applied by OSC1 
LFO1 (

Refer to the above “LFO1.”

▼ 2–1: Page Menu Command

☞0–1A: Write Program, 1–1A: Copy Oscillator, 1–1B: Swap 

These settings specify how key position (note number) will 
affect the pitch, and select the controllers that will affect the 
oscillator 2 pitch and specify the depth of control. They also 
specify the depth at which the pitch EG will affect the pitch of 
oscillator 2, and the depth of pitch change produced by LFO1 
and LFO2. Portamento on/off settings etc. are also found 
here.

For details on the functions of these parameters, refer to the 
preceding section “2–1: OSC1 P.Mod (OSC1 Pitch Mod.).”

Here you can make settings for the pitch EG, which creates 
time-variant changes in the pitch of oscillators 1 and 2.
The depth of pitch change produced by these EG settings on 
oscillator 1 (2) is adjusted by “Pitch EG” (2–1b, 2–2).

These settings specify how the pitch will change over time.

These parameters specify the amount of pitch change.
The actual amount of pitch change will depend on the 
“Pitch EG” (2–1b, 2–2) parameter “Intensity.” For example 
with an “Intensity” setting of +12.00, a “Level” setting of 
+99

 would raise the pitch one octave, and a “Level” setting 

of –99 would lower the pitch one octave.

Specifies the amount of pitch change at note-on.

Specifies the amount of pitch change when the attack time 
has elapsed.

Specifies the amount of pitch change when the release time 
has elapsed.

These parameters specify the amount of time over which the 
pitch change will occur.

Specifies the time over which the pitch will change from 
note-on until it reaches the pitch specified as the attack level.

Specifies the time over which the pitch will change after 
reaching the attack level until it reaches the normal pitch.

Specifies the time over which the pitch will change from note-
off until it reaches the pitch specified as the release level.

These settings allow the pitch EG Level parameters to be con-
trolled by alternate modulation.

Selects the source that will control the pitch EG Level param-
eters (“AMS List” 

Specifies the depth and direction of the effect applied by 
“AMS1 (Level Mod. AMS1).”
With a setting of 0, the levels specified by “Pitch EG” (2–3a) 
will be used.
For example if “AMS1 (Level Mod. AMS1)” is SW1:CC#80, 
pressing the [SW1] key to turn it on will change the Level 
parameters of the Pitch EG. (Set “Panel Switch Assign” (1–
4a) to SW1 Mod.CC#80.) As the absolute value of “Intensity 
(AMS1 Intensity)” is increased, the pitch EG levels will 
change more greatly when the [SW1] key is turned on. The 
direction of the change is specified by “St (AMS1 SW Start)” 
and “At (AMS1 SW Attack).” When the [SW1] key is turned 
off, the pitch EG levels will return to their own settings.
If “AMS1 (Level Mod. AMS1)” is set to Velocity, increasing 
the absolute value of “Intensity (AMS1 Intensity)” will pro-
duce increasingly wider change in pitch EG levels for 
strongly-played notes. The direction of the change is speci-
fied by “St (AMS1 SW Start)” and “At (AMS1 SW Attack).” 
As you play more softly, the pitch change will draw closer to 
the pitch EG levels.

2–3

2–3a

2–3c

2–3b

Note-on

Note-off

Attack
Time

Decay
Time

Start Level

Release Level

Release Time

Attack Level

+99 = approximately 1 octave

–99 = approximately 1 octave

0 = pitch when
key is held
(sustained)

Time

Time-varying pitch settings (when Pitch EG Intensity = +12.00)