Sharp PNE802 Manuel D’Utilisation

Menu Items

COPY SETTING VALUE
When the monitor has been connected to multiple monitors

by RS-232C, the settings in the monitor can be copied to the

monitor connected to the RS-232C output terminal and to

the daisy chain of connected monitors that follows.

Selects the settings to copy with COPY SETTING VALUE

TARGET.

“PICTURE” ONLY ..... Copies the PICTURE menu settings.*

ALL ........................... Copies all the settings.*

Select the ID No. of the monitor that you would like copy to

with COPY TO ID No., then select COPY and press

If you select ALL, settings will be copied to all monitors.

When you would like to confirm the ID No. that is set to the

monitor, select ID No. DISPLAY and press

. The ID No.

will be displayed on the screen.

* Certain setting details such as ANALOG GAIN, ANALOG

OFFSET, and DISPLAY COLOR PATTERN cannot be

copied.

LOGO SCREEN
Sets whether or not to display the logo screen.

OPTION

DATE/TIME SETTING
Set the date and time. Press

to select the date

and time, and press

to change the numerical

values.

Set the date in “Month/Day/Year” order.

Set the time on a 12-hour basis. (Factory default)
DATE/TIME FORMAT
Sets the date/time display format.

DATE ..................MM/DD/YYYY

DD/MM/YYYY

YYYY/MM/DD

(YYYY: Year, MM: Month, DD: Day)

TIME ...................Select 12- or 24-hour time.
SCHEDULE (See page 26.)
You can turn the power on/off and change the screen

brightness at a specified time.
INPUT SELECT
Select the input mode to be used in PC D-Sub input terminal,

PC/AV DVI-D input terminal, PC/AV HDMI input terminal and

PC RGB/AV component input terminals.

For D-SUB, select SET after selecting the input mode, and

then press

D-SUB and BNC cannot be set to AV COMPONENT at the

same time.

If D-SUB is set to AV VIDEO, the AV VIDEO input terminal

cannot be used for BNC.
AUDIO SELECT
Selects the terminal used to input audio signals in each input

mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input

terminal outputs any of the following resolutions, make a

selection from the following options.

480 LINES .......... AUTO, 640x480 or 848x480

768 LINES ..........AUTO, 1024x768, 1280x768, or 1360x768

1050 LINES ........1400x1050 or 1680x1050

ZOOM2 SPECIAL SETTING (See page 25.)

STANDBY MODE
When STANDARD is selected, startup time from standby

mode is reduced. Note, however that, more power will be

consumed in standby mode.

When LOW POWER is selected, current consumption

is reduced while the monitor is in standby mode. Note,

however, that the startup time from standby mode becomes

longer.

If set to LOW POWER, certain RS-232C commands cannot

be used in standby mode, and control via LAN will be

disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into

standby mode when there is no operation from the remote

control unit, RS-232C commands, or LAN for over 4 hours.
HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI

and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from

the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain

(see page 30), using the RS-232 cables.

The numbers 1 to 255 are available for ID numbers.

If “0” is set, the system regards this as the state where no ID

number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when

multiple monitors are connected with RS-232C.

Select ON, then press

Perform operations using the first monitor in the daisy chain.
BAUD RATE
Selects the communication speed used for RS-232C

communication.
LAN SETUP
Configures the settings to control the monitor from the

computer via LAN. (See page 41.)
AUTO ASSIGN FIXED IP ADDR.
Can be enabled when RS-232C/LAN SELECT is LAN and

the DHCP CLIENT is OFF.

Set DHCP CLIENT to OFF for the monitor connected to the

RS-232C output terminal and the daisy chain of connected

monitors that follows. Fixed IP addresses are automatically

allocated.

If the IP address is a duplicate with a network device other

than a monitor, individually change the IP address.
SPEAKER SELECT
Selects the speaker to be used.
HDMI AUTO VIEW
When ON is selected, the screen size is adjusted

automatically according to the screen size control signal

included in the video signal input from the AV HDMI input

terminal.