SMC Networks LH79520 SoC ARM720T Manuel D’Utilisation
ARM720T_LH79520 – Sharp LH79520 SoC with ARM720T 32-bit RISC Processor
Pin Description
The following pin description is for the processor when used on the schematic. In an OpenBus System, although the same
signals are present, the abstract nature of the system hides the pin-level Wishbone interfaces. The interface signals to the
physical processor will be made available as sheet entries, associated with the parent sheet symbol used to reference the
underlying OpenBus System.
signals are present, the abstract nature of the system hides the pin-level Wishbone interfaces. The interface signals to the
physical processor will be made available as sheet entries, associated with the parent sheet symbol used to reference the
underlying OpenBus System.
Table 1. ARM720T_LH79520 pin description
Name Type
Polarity/Bus
size
Description
Control Signals
CLK_I
I Rise
External (system) clock. This signal is internally wired to the
ARM7_SYS_CLK output.
ARM7_SYS_CLK output.
RST_I
I High
External (system) reset. This signal is internally wired to the
ARM7_SYS_RESET output
ARM7_SYS_RESET output
Interrupt Signals
INT_I
I 32
Interrupt lines. The least significant 5 lines are routed through to the
physical device on the PER_INT bus (see
physical device on the PER_INT bus (see
External Memory Interface Signals
ME_STB_O
O High
Strobe signal. When asserted, indicates the start of a valid Wishbone
data transfer cycle
data transfer cycle
ME_CYC_O
O High
Cycle signal. When asserted, indicates the start of a valid Wishbone
bus cycle. This signal remains asserted until the end of the bus
cycle, where such a cycle can include multiple data transfers
bus cycle. This signal remains asserted until the end of the bus
cycle, where such a cycle can include multiple data transfers
ME_ACK_I
I High
Standard Wishbone device acknowledgement signal. When this
signal goes High, an external Wishbone slave memory device has
finished execution of the requested action and the current bus cycle
is terminated
signal goes High, an external Wishbone slave memory device has
finished execution of the requested action and the current bus cycle
is terminated
ME_ADR_O
O 32
Standard Wishbone address bus, used to select an address in a
connected Wishbone slave memory device for writing to/reading
from
connected Wishbone slave memory device for writing to/reading
from
ME_DAT_I
I 32
Data received from an external Wishbone slave memory device
ME_DAT_O
O 32
Data to be sent to an external Wishbone slave memory device
ME_SEL_O
O 4
Select output, used to determine where data is placed on the
ME_DAT_O line during a Write cycle and from where on the
ME_DAT_I line data is accessed during a Read cycle. Each of the
data ports is 32-bits wide with 8-bit granularity, meaning data
transfers can be 8-, 16- or 32-bit. The four select bits allow targeting
of each of the four active bytes of a port, with bit 0 corresponding to
the low byte (7..0) and bit 3 corresponding to the high byte (31..24)
ME_DAT_O line during a Write cycle and from where on the
ME_DAT_I line data is accessed during a Read cycle. Each of the
data ports is 32-bits wide with 8-bit granularity, meaning data
transfers can be 8-, 16- or 32-bit. The four select bits allow targeting
of each of the four active bytes of a port, with bit 0 corresponding to
the low byte (7..0) and bit 3 corresponding to the high byte (31..24)
ME_WE_O
O
Level
Write enable signal. Used to indicate whether the current local bus
cycle is a Read or Write cycle.
cycle is a Read or Write cycle.
0 = Read
1 = Write
ME_CLK_O
O Rise
External (system) clock signal (identical to CLK_I), made available
for connecting to the CLK_I input of a slave memory device. Though
not part of the standard Wishbone interface, this signal is provided
for convenience when wiring your design
for connecting to the CLK_I input of a slave memory device. Though
not part of the standard Wishbone interface, this signal is provided
for convenience when wiring your design
ME_RST_O
O High
Reset signal made available for connection to the RST_I input of a
slave memory device. This signal goes High when an external reset
is issued to the processor on its RST_I pin. When this signal goes
Low, the reset cycle has completed and the processor is active
again. Though not part of the standard Wishbone interface, this
signal is provided for convenience when wiring your design
slave memory device. This signal goes High when an external reset
is issued to the processor on its RST_I pin. When this signal goes
Low, the reset cycle has completed and the processor is active
again. Though not part of the standard Wishbone interface, this
signal is provided for convenience when wiring your design
6
CR0162 (v2.0) March 10, 2008