IBM XSERIES 220 Manuel D’Utilisation
94
Hardware Maintenance Manual: xSeries 220
•
Cisco Fast EtherChannel
(FEC) creates a team of two to four adapters to increase
transmission and reception thoughput. FEC also includes the AFT option. You can
use FEC only with a switch that has FEC capability.
use FEC only with a switch that has FEC capability.
Teaming requires you to install at least one additional Ethernet adapter. For additional
information about the teaming modes, refer to the documentation that comes with
these additional adapters.
information about the teaming modes, refer to the documentation that comes with
these additional adapters.
Priority Packet Mode:
Priority Packet is a traffic-prioritization utility that you can
use to set up filters to process high-priority traffic before normal traffic. You can send
information from critical nodes or applications with an indicated priority. Because
you set this priority at the host or entry point of the network, the network devices can
base forwarding decisions on priority information that is defined in the packet.
information from critical nodes or applications with an indicated priority. Because
you set this priority at the host or entry point of the network, the network devices can
base forwarding decisions on priority information that is defined in the packet.
Priority Packet information is available on the IBM Networking Web site at
http://www.ibm.com/networking/support
http://www.ibm.com/networking/support
Priority Packet prioritizes traffic based on priority filters. These are parameters that
you assign to outgoing (transmit) packets. Using the Priority Filter Wizard, you can
set up predefined or custom priority filters based on a node (MAC) address, Ethernet
type, or by various properties of the protocol and port. Priority Packet provides two
different methods for prioritizing traffic: IEEE 802.1p tagging and High Priority
Queue.
you assign to outgoing (transmit) packets. Using the Priority Filter Wizard, you can
set up predefined or custom priority filters based on a node (MAC) address, Ethernet
type, or by various properties of the protocol and port. Priority Packet provides two
different methods for prioritizing traffic: IEEE 802.1p tagging and High Priority
Queue.
IEEE 802.1p is a new IEEE standard for tagging, or adding additional bytes of
information to packets with different priority levels. Packets are tagged with 4
additional bytes, which increase the packet size and indicate a priority level. When
you send these packets out on the network, the higher priority packets are transferred
first. Priority packet tagging (also known as Traffic Class Expediting) enables the
adapter to work with other elements of the network (such as switches and routers) to
deliver priority packets first. You can assign specific priority levels from 0 (low) to 7
(high).
information to packets with different priority levels. Packets are tagged with 4
additional bytes, which increase the packet size and indicate a priority level. When
you send these packets out on the network, the higher priority packets are transferred
first. Priority packet tagging (also known as Traffic Class Expediting) enables the
adapter to work with other elements of the network (such as switches and routers) to
deliver priority packets first. You can assign specific priority levels from 0 (low) to 7
(high).
You can assign values to packets based on their priority when you use the IEEE 802.1p
standard for packet tagging. This method requires a network infrastructure that
supports packet tagging. The routing devices that receive and transfer these packets
on your network must support 802.1p for tagging to be effective.
standard for packet tagging. This method requires a network infrastructure that
supports packet tagging. The routing devices that receive and transfer these packets
on your network must support 802.1p for tagging to be effective.
After you set up the priority filter in Priority Packet, you must start IBMSet and select
802.1p/802.1Q Tagging
802.1p/802.1Q Tagging
on the Advanced tab.
Note:
IEEE 802.1p tagging increases the size of the packets that it tags. Some hubs
and switches will not recognize the larger packets and will drop them. Check
your hub or switch documentation to see if they support 802.1p. (You can
configure the switch to strip the tags from the packets and send it on to the
next destination as normal traffic.) If these devices do not support 802.1p or if
you are not sure, use High Priority Queue (HPQ) to prioritize network traffic.
and switches will not recognize the larger packets and will drop them. Check
your hub or switch documentation to see if they support 802.1p. (You can
configure the switch to strip the tags from the packets and send it on to the
next destination as normal traffic.) If these devices do not support 802.1p or if
you are not sure, use High Priority Queue (HPQ) to prioritize network traffic.
The requirements for effectively using IEEE 802.1p tagging are:
•
The other devices receiving and routing 802.1p tagged packets must support
802.1p.
802.1p.
•
The adapters on these devices must support 802.1p. The Ethernet controller in the
xSeries 220 and all IBM 10/100 Ethernet Security Adapters support 802.1p.
xSeries 220 and all IBM 10/100 Ethernet Security Adapters support 802.1p.
•
The adapter cannot be assigned to an adapter team.
•
If you are setting up VLANs and packet tagging on the same adapter,
802.1p/802.1Q tagging must be enabled on the IBMSet Advanced tab.
802.1p/802.1Q tagging must be enabled on the IBMSet Advanced tab.
If your network infrastructure devices do not support IEEE 802.1p or you are not sure,
you can still define filters and send packets as high priority. While High Priority
you can still define filters and send packets as high priority. While High Priority