Renesas M3062PT2-EPB Manuel D’Utilisation
M3062PT2-EPB User’s Manual
1. Outline
REJ10J0868-0200 Rev.2.00 January 16, 2006
Page 18 of 102
1.4 Specifications
Tables 1.5 and 1.6 list the specifications of the M3062PT2-EPB.
Table 1.5 Specifications of the M3062PT2-EPB (1/2)
Table 1.5 Specifications of the M3062PT2-EPB (1/2)
Applicable MCU
M16C/60 Series M16C/62P Group and M16C/30 Series M16C/30P Group MCUs
Applicable MCU mode
Single-chip mode
Memory expansion mode (NORMAL, 4MB)
Microprocessor mode (NORMAL, 4MB)
Memory expansion mode (NORMAL, 4MB)
Microprocessor mode (NORMAL, 4MB)
Maxi. ROM/RAM capacity
1. Internal flash ROM: 516KB
0F000h--0FFFFh, 80000h--FFFFFh
2. Internal RAM: 31KB
00400h--07FFFh
Applicable power supply
Vcc1 = Vcc2: 2.7--5.5 V
Vcc1 > Vcc2: Vcc1 = 5.0 ± 0.2 V, 2.7 V ≤ Vcc2 < Vcc1
Vcc1 > Vcc2: Vcc1 = 5.0 ± 0.2 V, 2.7 V ≤ Vcc2 < Vcc1
Maximum operating frequency
3.0 to 5.5 V: 24 MHz (when using a PLL)
2.7 V: 10 MHz
2.7 V: 10 MHz
Emulation memory
1. Max. operating frequency of ROM area
10 MHz
2. External area (CS3# -- CS0# area) Minimum 4KB x 4 areas
- Maximum operating frequency (at 5.0 V) 0 wait:
7 MHz
1 wait:
20 MHz
2 wait, 3 wait:
24 MHz
- Maximum operating frequency (at 3.0 V) 0 wait:
6 MHz
1 wait:
17 MHz
2 wait, 3 wait:
24MHz
Basic debugging functions
- Download
- Address match break (max. 8 points)
- Software break (max. 64 points)
- Program execution/stop (allows free-run execution supporting software breaks)
- Memory reference/setting (reference/setting C-variables, run-time execution)
- Register reference/setting
- Disassemble display
- C-level debugging, etc.
- Address match break (max. 8 points)
- Software break (max. 64 points)
- Program execution/stop (allows free-run execution supporting software breaks)
- Memory reference/setting (reference/setting C-variables, run-time execution)
- Register reference/setting
- Disassemble display
- C-level debugging, etc.
Real-time trace function
- 256K-cycle bus information recordable
(Bus, external trigger, time stamp)
- 5 trace modes supported (Break/Before/About/After/Full)
- Can be recorded ON/OFF by events
- Can be recorded ON/OFF by events
Real-time RAM monitor function
- 4,096 bytes (256 bytes x16)
- Data/last access result
- Data/last access result
Hardware break function
8 points (Execution address, bus detection, interrupt, external trigger signal)
Execution time measurement function Time between program start and stop
Maximum/minimum/average execution time and pass count of specified four zones.
Count clock: Equal to MCU Clock or 16 MHz
Count clock: Equal to MCU Clock or 16 MHz
C0 coverage
8,192 KB (256 KB x 32 blocks)
External trigger input/event output
External trigger input (MCU-dependent-voltage CMOS level x8) or event output
(break x1, event x7)
(break x1, event x7)
Host machine interface
- LPT parallel (ECP, EEP, Byte/compatibility and Nibble/compatibility modes)
- USB (USB 1.1, full-speed)*
- LAN (10BASE-T)
- USB (USB 1.1, full-speed)*
- LAN (10BASE-T)
Power supply to emulator
Supplied from included AC adapter (power supply voltage: 100--240 V, 50/60 Hz)
* Available to connect the host machine that supports USB 2.0.
With the USB interface, not all hardware (such as host machine, USB devices, USB hub) combination will work and
guaranteed.
guaranteed.