Mitsubishi Electronics WL7200U Manuel D’Utilisation

EN-56

This projector is equipped with a roll-up filter. The 

clogged filter rolls and replaces with a clean one 

periodically. When all the filters are rolled up, you can 

replace the filter cartridge with a new one. 

•  When the power of the projector is on, the filter

rolls after the designated time elapses. 

•  There are 10 filters per cartridge. When a filter rolls,

REMAINING FILTERS is decreased and FILTER 

USAGE TIME is reset.

•  When REMAINING FILTERS reaches 0, the FILTER 

indicator blinks red. In this case, prepare a new filter 

cartridge. When the last filter is clogged, replace the 

filter cartridge. For details, contact your dealer.

•  Depending on the ambient environment, the filter

may run out before rolling 9 times and the FILTER 

indicator may blink orange while the projector is 

turned on. In this case, replace the filter cartridge. 

For details contact your dealer.

•  Do not clean the filter yourself. It may cause

malfunction.

•  Do not rewind the filter. It may cause malfunction.

You can set the roll interval of the roll-up filter using 

the menu. 
(See page 31 for menu setting.)
1.  Display the FEATURE menu.
2.  Select FILTER MENU by pressing the  or  button. 

3.  Press the ENTER button.
4.  Select AUTO ROLL UP PERIOD by pressing the  

or  button. 

5.  Select OFF, EVERY 500H, EVERY 750H or EVERY 

1000H by pressing the  or  button.
OFF .................The filter does not roll automatically. 

Roll the filter manually when the filter 
is clogged. 

EVERY 500H ...The filter rolls about every 500 hours. 

EVERY 750H ...The filter rolls about every 750 hours.

EVERY 1000H ..The filter rolls about every 1000 hours.

Important:
•  If you select the interval which is shorter than the current 

filter usage time, the filter rolls once after 1 minute.

(See page 31 for menu setting.)
1.  Display the FEATURE menu.
2.  Select FILTER MENU by pressing the  or  button. 

3.  Press the ENTER button.
4.  Select MANUAL ROLL UP by pressing the  or  

button. 

5.  Press the ENTER button.

•  Confirmation dialog appears.

MANUAL ROLL UP ?

OK : ENTER   CANCEL : MENU

6.  Press the ENTER button or MENU button.

•  When you press the ENTER button, the filter

rolls once.

•  To cancel the setting, press the MENU button.

When the filter rolls 9 times, the FILTER indicator blinks 
red. In this case, prepare a new filter cartridge. When 
the last filter is clogged, replace the filter cartridge. 
Before replacing the filter, be sure to turn off the power of 
the projector and unplug the power cord from the outlet. 
1.  Unplug the power cord.
2.  Loosen two screws (a) that is securing the filter 

cover using a Philips screwdriver and remove the 
filter cover (b) from the projector. 

(a)

     

(b)

3.  Remove the roll-up filter cartridge. 

    

Roll-up filter cartridge

4.  Attach a new roll-up filter cartridge. 

     

5.  Insert the filter cover (b) into the projector and 

tighten two screws (a) on the filter cover firmly 
using a Philips screwdriver. 

(b)

 

(a)

Reset of the roll counter of the filter
Plug in the power cord and reset the roll counter of the 
filter (REMAINING FILTERS and FILTER USAGE TIME)
by holding down the , , and ENTER/GEOMETRY 
buttons on the control panel at the same time about 3 
seconds.
Important:
•  Unless these 3 buttons are pressed at the same 

time, the counter isn’t reset.

•  Make sure that the FILTER indicator blinks 3 times 

and the counter is reset successfully.

•  The projector doesn’t turn on if the filter cartridge 

or the filter cover isn’t attached securely.

•  Do not reset the counter unless you replace the 

filter cartridge.