Q-Logic 59022-11 A 4-13 Manuel D’Utilisation
A – Command Line Interface
Set Config Command
Set Config Command
A-62
59022-11 A
0
security
Initiates an editing session in which to change the security settings. The system
displays each parameter one line at a time and prompts you for a value. For each
Initiates an editing session in which to change the security settings. The system
displays each parameter one line at a time and prompts you for a value. For each
LCFEnable
Link control frame preference routing. This parameter
appears only if AutoPerfTuning is False. Enables (True) or
disables (False) preferred routing of frames with R_CTL =
1100 (Class 2 responses). The default is False. Enabling
LCFEnable will disable MFSEnable.
appears only if AutoPerfTuning is False. Enables (True) or
disables (False) preferred routing of frames with R_CTL =
1100 (Class 2 responses). The default is False. Enabling
LCFEnable will disable MFSEnable.
MFSEnable
Multi-Frame Sequence bundling. This parameter appears
only if AutoPerfTuning is False. Prevents (True) or allows
(False) the interleaving of frames in a sequence. The default
is True. Enabling MFSEnable disables LCFEnable and
VIEnable.
only if AutoPerfTuning is False. Prevents (True) or allows
(False) the interleaving of frames in a sequence. The default
is True. Enabling MFSEnable disables LCFEnable and
VIEnable.
VIEnable
Virtual Interface (VI) preference routing. This parameter
appears only if AutoPerfTuning is False. Enables (True) or
disables (False) VI preference routing. The default is False.
Enabling VIEnable will disable MFSEnable.
appears only if AutoPerfTuning is False. Enables (True) or
disables (False) VI preference routing. The default is False.
Enabling VIEnable will disable MFSEnable.
MSEnable
Management server enable. Enables (True) or disables
(False) management server on this port. The default is True.
(False) management server on this port. The default is True.
NoClose
Loop circuit closure prevention. Enables (True) or disables
(False) the loop’s ability to remain in the open state
indefinitely. True reduces the amount of arbitration on a loop
when there is only one device on the loop. The default is
False.
(False) the loop’s ability to remain in the open state
indefinitely. True reduces the amount of arbitration on a loop
when there is only one device on the loop. The default is
False.
IOStreamGuard
I/O Stream Guard. Enables or disables the suppression of
RSCN messages. IOStreamGuard can have the following
values:
RSCN messages. IOStreamGuard can have the following
values:
Enable – Suppresses the reception of RSCN messages
from other ports for which IOStreamGuard is enabled.
from other ports for which IOStreamGuard is enabled.
Disable – Allows free transmission and reception of
RSCN messages.
RSCN messages.
Auto – Suppresses the reception of RSCN messages
when the port is connected to an initiator device with a
QLogic HBA. For older QLogic HBAs, such as the
QLA2200, the DeviceScanEnabled parameter must also
be enabled. The default is Auto.
when the port is connected to an initiator device with a
QLogic HBA. For older QLogic HBAs, such as the
QLA2200, the DeviceScanEnabled parameter must also
be enabled. The default is Auto.
PDISCPingEnable
Enables (True) or disables (False) the transmission of ping
messages from the switch to all devices on a loop port. The
default is True.
messages from the switch to all devices on a loop port. The
default is True.
Table A-18. Set Config Port Parameters
Parameter
Description