Grandstream gxw-4004 Manuel D’Utilisation
Grandstream Networks, Inc.
GXW400x User Manual
Page 10 of 36
Firmware 1.0.1.8
Last Updated: 5/2008
B
ASIC
O
PERATIONS
U
NDERSTANDING
GXW
V
OICE
P
ROMPTS
GXW400x has a built-in voice prompt menu for simple device configuration. To enter the voice prompt
menu, press *** on the standard analog phone connected to any FXS port.
menu, press *** on the standard analog phone connected to any FXS port.
T
ABLE
5:
D
EFINITIONS OF THE
GXW
V
OICE
P
ROMPTS
Menu
Voice Prompt
User’s Options
Main Menu
“Enter a Menu Option”
Enter “*” for the next menu option
Enter “#” to return to the main menu
Enter 01 – 05, 07,10 - 17, 47, 86 or 99 Menu option
Enter “#” to return to the main menu
Enter 01 – 05, 07,10 - 17, 47, 86 or 99 Menu option
01
“DHCP Mode”, “PPPoE
Mode ”or “Static IP Mode”
Mode ”or “Static IP Mode”
Enter ‘9’ to toggle the selection
If user selects “Static IP Mode”, user need configure all the IP
address information through menu 02 to 05. If user selects
“Dynamic IP Mode”, the device will retrieve all IP address
information from DHCP server automatically when user reboots
the device.
If user selects “Static IP Mode”, user need configure all the IP
address information through menu 02 to 05. If user selects
“Dynamic IP Mode”, the device will retrieve all IP address
information from DHCP server automatically when user reboots
the device.
02
“IP Address “ + IP address
The current WAN IP address is announced
Enter 12-digit new IP address if in Static IP Mode.
Enter 12-digit new IP address if in Static IP Mode.
03
“Subnet “ + IP address
Same as Menu option 02
04
“Gateway “ + IP address
Same as Menu option 02
05
“DNS Server “ + IP address
Same as Menu option 02
07
Preferred Vocoder
Enter “9” to go to the next selection in the list:
•
PCM U
• PCM
A
• iLBC
• G-726
• G-726
•
G-723
• G-729
10
“MAC Address”
Announces the Mac address of the unit.
12
WAN Port Web Access
Enter “9” to toggle between enable and disable
13
Firmware Server IP Address
Announces current Firmware Server IP address. Enter 12 digit
new IP address.
new IP address.
14
Configuration Server IP
Address
Address
Announces current Config Server Path IP address. Enter 12 digit
new IP address.
new IP address.
15
Upgrade Protocol
Upgrade protocol for firmware and configuration update. Enter “9”
to toggle between TFTP and HTTP
to toggle between TFTP and HTTP
16
Firmware Version
Firmware version information.
17
Firmware Upgrade
Firmware upgrade mode. Enter “9” to rotate among the following
three options:
three options:
1. always
check
2. check when pre/suffix changes
3. never
3. never
upgrade
47
“Direct IP Calling”
Enter the target IP address to make a direct IP call, after dial
tone. (See “Make a Direct IP Call”.)
tone. (See “Make a Direct IP Call”.)
71-78
Phone calls between different
ports of the same GW in case
no SIP server is in use
ports of the same GW in case
no SIP server is in use
User can make internal calls between different ports inside the
same GW even without being registered to SIP server. By dialing
*** and 7x user can reach colleague connected to port “x”
same GW even without being registered to SIP server. By dialing
*** and 7x user can reach colleague connected to port “x”
86
Voice Mail
Number of voice mails
99
“RESET”
Enter “9” to reboot the device; or
Enter MAC address to restore factory default setting
(See Restore Factory Default Setting section)
(See Restore Factory Default Setting section)
“Invalid Entry”
Automatically returns to Main Menu