Electrovoice cp1200 Mode D'Emploi
Congratulations!
With buying a Electro-Voice CP-SERIES power amplifi er you have chosen an appli-
ance that employs most advanced technology.
CP-Series power amps combine outstanding audio performance, highest reliability and operational
safety.
CP-Series power amps combine outstanding audio performance, highest reliability and operational
safety.
The audio performance of CP power amps are simply extraordinary. Optimised power supply units
employing low-leakage toroidal transformers and the consistent use of Class-H technology provide ex-
tensive headroom far above the stated nominal output. At the same time this contributes to a reduction
in weight and power dissipation.
The CP1800/CP2200 is designed in Class-H technology (CP1200 Class-AB), i.e. the power amp provides
extremely fast, signal-dependent operating voltage switching, which results in doubling the regular
supply voltage when needed. Compared to Class-AB power amps, Class-H power amps generate by
far less power dissipation at identical output. Consequently, reduced leakage power or dissipation is
synonymous to less waste heat – energy is used more effi ciently. As a result, installing Class-H power
amps within rack shelf systems is possible with less space between appliances. In addition to that and
despite offering identical output, power consumption is a lot less than in Class-AB operation.
Electro-Voice CP-SERIES power amps have been designed to fulfi l even the most demanding
requirements of touring applications. CP-Series amps are protected against thermal and electrical
overload, short circuit and the occurrence of HF/DC at the outputs. Back-EMF-Protection eliminates
the risk of the output transistors being damaged by electrical energy back-feed. The power outputs are
switched via relay with a time delay during soft-start. An inrush current limiter prevents mains fuses from
blowing.
employing low-leakage toroidal transformers and the consistent use of Class-H technology provide ex-
tensive headroom far above the stated nominal output. At the same time this contributes to a reduction
in weight and power dissipation.
The CP1800/CP2200 is designed in Class-H technology (CP1200 Class-AB), i.e. the power amp provides
extremely fast, signal-dependent operating voltage switching, which results in doubling the regular
supply voltage when needed. Compared to Class-AB power amps, Class-H power amps generate by
far less power dissipation at identical output. Consequently, reduced leakage power or dissipation is
synonymous to less waste heat – energy is used more effi ciently. As a result, installing Class-H power
amps within rack shelf systems is possible with less space between appliances. In addition to that and
despite offering identical output, power consumption is a lot less than in Class-AB operation.
Electro-Voice CP-SERIES power amps have been designed to fulfi l even the most demanding
requirements of touring applications. CP-Series amps are protected against thermal and electrical
overload, short circuit and the occurrence of HF/DC at the outputs. Back-EMF-Protection eliminates
the risk of the output transistors being damaged by electrical energy back-feed. The power outputs are
switched via relay with a time delay during soft-start. An inrush current limiter prevents mains fuses from
blowing.
Mechanical construction and workmanship also comply with the highest precision manufacturing
standards. The rigid sheet steel chassis even resists the most wearing tour operation. Two three-speed
high performance fans (off/slow/fast) guarantee outstanding thermal stability at absolute low running
noise. The ventilation is directed front-to-rear allowing trouble-free operation even in smaller amp-racks.
The electronically balanced inputs are carried out via XLR-type connectors. Direct-Outs for through
connecting the audio signal are also provided via XLRM-type connectors. Input Routing allows selecting
DUAL (stereo) or PARALLEL (monaural) operation mode. By means of the separate BRIDGED OUT-
connector and a Bridged Mode-switch, switching to „Mono Bridged“ operation is truly uncomplicated
as well. The recessed mounted dB-scaled level controls ensure reliable protection against mechanical
damage. These particularly precise, secure to operate detent-potentiometers are located on the front
panel. CP-Series power amps provide the opportunity for retrofi tting an internal analogue signal
standards. The rigid sheet steel chassis even resists the most wearing tour operation. Two three-speed
high performance fans (off/slow/fast) guarantee outstanding thermal stability at absolute low running
noise. The ventilation is directed front-to-rear allowing trouble-free operation even in smaller amp-racks.
The electronically balanced inputs are carried out via XLR-type connectors. Direct-Outs for through
connecting the audio signal are also provided via XLRM-type connectors. Input Routing allows selecting
DUAL (stereo) or PARALLEL (monaural) operation mode. By means of the separate BRIDGED OUT-
connector and a Bridged Mode-switch, switching to „Mono Bridged“ operation is truly uncomplicated
as well. The recessed mounted dB-scaled level controls ensure reliable protection against mechanical
damage. These particularly precise, secure to operate detent-potentiometers are located on the front
panel. CP-Series power amps provide the opportunity for retrofi tting an internal analogue signal
processor board with x-over and fi lter functions.
The easily readable LED display provides a quick overview of the power amp’s current operational
status. The power outputs CHANNEL A, CHANNEL B and BRIDGED OUT are carried out as extremely
durable SPEAKON-type connectors. Also located on the rear panel is a Ground-lift switch, which helps
eliminating ground-noise loops by separating the power amp’s enclosure from the circuit ground. In
normal operation, all CP-Series power amps are capable of driving loads as low as 2ohms. In Mono-
Bridged mode the allowable minimum load is 4ohms.
This owner’s manual outlines and explains several other features of your CP-Series power amplifi er.
Please, make sure to carefully read all of it and mind the instructions.
The easily readable LED display provides a quick overview of the power amp’s current operational
status. The power outputs CHANNEL A, CHANNEL B and BRIDGED OUT are carried out as extremely
durable SPEAKON-type connectors. Also located on the rear panel is a Ground-lift switch, which helps
eliminating ground-noise loops by separating the power amp’s enclosure from the circuit ground. In
normal operation, all CP-Series power amps are capable of driving loads as low as 2ohms. In Mono-
Bridged mode the allowable minimum load is 4ohms.
This owner’s manual outlines and explains several other features of your CP-Series power amplifi er.
Please, make sure to carefully read all of it and mind the instructions.
DESCRIPTION
4