Cisco Cisco Firepower Management Center 2000 Manuel Technique
Mod-sfr 795> ***
Mod-sfr 796> *** EVENT: Disk Image created successfully.
Mod-sfr 797> *** TIME: 05:53:06 UTC Jul 1 2014
Mod-sfr 798> ***
Mod-sfr 799> ***
Mod-sfr 800> *** EVENT: Start Parameters: Image: /mnt/disk0/vm/vm_3.img,
ISO: -cdrom /mnt/disk0
Mod-sfr 801> /asasfr-5500x-boot-5.3.1-152.img, Num CPUs: 6, RAM: 7659MB,
Mgmt MAC: A4:4C:11:29:
Mod-sfr 802> CC:FB, CP MAC: 00:00:00:04:00:01, HDD: -drive file=/dev/md0,
cache=none,if=virtio,
Mod-sfr 803> Dev
Mod-sfr 804> ***
Mod-sfr 805> *** EVENT: Start Parameters Continued: RegEx Shared Mem:
32MB, Cmd Op: r, Shared M
Mod-sfr 806> em Key: 8061, Shared Mem Size: 64, Log Pipe: /dev/ttyS0_vm3,
Sock: /dev/ttyS1_vm3,
Mod-sfr 807> Mem-Path: -mem-path /hugepages
Mod-sfr 808> *** TIME: 05:53:06 UTC Jul 1 2014
Mod-sfr 809> ***
Mod-sfr 810> IVSHMEM: optarg is key=8061,64,unix:/tmp/nahanni, name is,
key is 8061, size is 6
...
Mod-sfr 239> Starting Advanced Configuration and Power Interface daemon:
acpid.
Mod-sfr 240> acpid: starting up with proc fs
Mod-sfr 241> acpid: opendir(/etc/acpi/events): No such file or directory
Mod-sfr 242> starting Busybox inetd: inetd... done.
Mod-sfr 243> Starting ntpd: done
Mod-sfr 244> Starting syslogd/klogd: done
Mod-sfr 245>
Cisco ASA SFR Boot Image 5.3.1
Wait approximately 5 to 15 minutes for the ASA SFR module to boot up, and then open a
console session to the operational ASA SFR boot image.
console session to the operational ASA SFR boot image.
5.
Set Up the ASA SFR Boot Image
Complete these steps in order to set up the the newly installed ASA SFR boot image:
Press Enter after you open a session in order to reach the login prompt. Note: The default
username is admin, and the default password is Admin123.Here is an example:
username is admin, and the default password is Admin123.Here is an example:
ciscoasa# session sfr console
Opening console session with module sfr.
Connected to module sfr. Escape character sequence is 'CTRL-^X'.
Cisco ASA SFR Boot Image 5.3.1
asasfr login: admin
Password: Admin123
Tip: If the ASA SFR module boot has not completed, the session command fails and a
message appears to indicate that the system is unable to connect over TTYS1. If this occurs,
wait for the module boot to complete and try again.
message appears to indicate that the system is unable to connect over TTYS1. If this occurs,
wait for the module boot to complete and try again.
1.
Enter the setup command in order to configure the system so that you can install the system
software package:
software package:
asasfr-boot> setup
Welcome to SFR Setup
[hit Ctrl-C to abort]
Default values are inside []
You are then prompted for this information:Host name - The host name can be up to 65
2.