Cisco Cisco IOS Software Release 12.2(10)
![Cisco](https://files.manualsbrain.com/attachments/7380d0050044647c30f5c24bbbf5d0c0b6d9bb84/common/fit/150/50/faa183d287233c52228cfea3dbc2a127fe780f60564fcb0955d9c3d1cd23/brand_logo.png)
19
Resolved Caveats—Release 12.2(5)DA
OL-2702-01
Caveats
Resolved Caveats—Release 12.2(5)DA
The problems listed in
are fixed in Cisco IOS Release 12.2(5)DA.
CSCdv86663
When you configure an interface bandwidth statement on a Cisco 6260 ATM
interface, the default bandwidth value for the interface as seen in the show
interface atm command may appear in the show running-config output.
interface, the default bandwidth value for the interface as seen in the show
interface atm command may appear in the show running-config output.
CSCdw03128
Cisco 6260 SNMP agent returns wrong ifType for SHDSL interfaces.
CSCdw25440
Using the command show atm vc interface atm slot/port vpi vci where vpi and vci
are the vpi and vci numbers in a SVC configuration can cause the DSLAM to
reload. This usually happens when the CPE is connected but the SVC is not yet
established.
are the vpi and vci numbers in a SVC configuration can cause the DSLAM to
reload. This usually happens when the CPE is connected but the SVC is not yet
established.
CSCdw34798
Invalid cells are passed to network port on a valid VC. The 4xDMT line card does
not discard cells with HEC errors and stamps each cell going to the DSLAM with
a valid HEC. The switch can then pass these corrupt cells out the WAN interface if
they appear to have a valid and provisioned VPI and VCI.
not discard cells with HEC errors and stamps each cell going to the DSLAM with
a valid HEC. The switch can then pass these corrupt cells out the WAN interface if
they appear to have a valid and provisioned VPI and VCI.
CSCdw41743
After 54 days of uptime, the system experienced an unexpected reload immediately
preceded by the messages: System reloads with message SYS-2-WATCHDOG
process=IMA CORE.
preceded by the messages: System reloads with message SYS-2-WATCHDOG
process=IMA CORE.
CSCdw47576
An NI-2 DSLAM reloads after a few ALIGN-1-FATAL error messages.
CSCdw65903
An error can occur with management protocol processing. Please use the following
URL for further information:
URL for further information:
Table 10
Caveats Resolved in Cisco IOS Release 12.2(7)DA (continued)
Caveat Number
Description
Table 11
Caveats Resolved in Cisco IOS Release 12.2(5)DA
Caveat Number
Description
CSCdt89256
Cisco 6160 DSLAM does not recognize the debug atm oam command.
CSCdt91908
When an IMA group and some of the links in the group are administratively
shutdown, the IMA group cannot recover.
shutdown, the IMA group cannot recover.
CSCdu06659
GETNEXT fails for all entries in cAdslAtucDmtChanTable.
CSCdu06678
GETNEXT fails for all entries in cAdslAturDmtChanTable.
CSCdu15630
Auto-sync of startup-config does not always work.
CSCdu17222
The port state that the show aps command displays for the subtend port on the
standby card is not valid until the peer state indicated by the command
show redundancy states is "STANDBY READY".
standby card is not valid until the peer state indicated by the command
show redundancy states is "STANDBY READY".
CSCdu18944
When both NI-2s in a redundant configuration reboot simultaneously, the standby
card may reboot more than once if the configuration file is very large.
card may reboot more than once if the configuration file is very large.
CSCdu24772
System shows secondary running config failed during RF progression.
CSCdu35414
Auto-sync of running config can cause write command to fail.
CSCdu44723
The show facility-alarm status command displays incorrect message.