Samsung RFG23UERS Manuel D’Utilisation
02 OPERA
TING
01 SETTING UP
Setting up
_19
1. Slip the compression nut through the supplied
plastic tubing
.
2. Tighten the compression nut
onto the 6.35 mm
compression fi tting.
-
If you are using copper tubing, slip the compression
nut
nut
(not included) and ferrule (not included) on
copper tubing (not included) as shown.
-
If you are using plastic tubing
, insert the
molded end(Bulb) of the plastic tubing
into the
compression fi tting.
Do not use without the molded end(Bulb) of the
plastic tubing
plastic tubing
.
3. Tighten the compression nut
onto the
compression fi tting. Do not over-tighten the
compression nut
compression nut
.
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable water
source. If you have to repair or disassemble
source. If you have to repair or disassemble
the water line, cut off 6.35 mm of the plastic tubing to
make sure you get a snug, leak-free connection.
make sure you get a snug, leak-free connection.
Installing the water fi lter.
1. Remove the water fi lter cover
1
.
2. Remove the fi xed cap by turning it counter
clockwise. Keep the cap in a safe place for later
use if you don’t use the fi lter.
use if you don’t use the fi lter.
3. Remove the water fi lter from the box and put
a replacement indicator sticker on the fi lter as
shown. Place the sticker on the fi lter that dates six
months in the future. For example, if you install the
water fi lter in March, put the “SEP” sticker on the
fi lter to remind you to replace it in September. That
way you’ll know when it is time to replace the fi lter.
Normally, a fi lter life is about 6 months.
shown. Place the sticker on the fi lter that dates six
months in the future. For example, if you install the
water fi lter in March, put the “SEP” sticker on the
fi lter to remind you to replace it in September. That
way you’ll know when it is time to replace the fi lter.
Normally, a fi lter life is about 6 months.
4. Remove the fi lter cap and insert the fi lter into the
fi lter housing.
5. Slowly turn the water fi lter 90º clockwise to align
with the printing mark on the cover, locking the
fi lter in position.
fi lter in position.
Make sure to align the water fi lter label mark
with center of cover fi lter printing as illustrated.
Remember, do not overtighten.
Remember, do not overtighten.
You should remove the right side upper glass
shelf before installing the water fi lter.
shelf before installing the water fi lter.
Removing any residual matter inside
the water supply line after installing
the water fi lter.
the water supply line after installing
the water fi lter.
1. Turn ON the main water supply & turn OFF the
valve to the water supply line.
2. Run water through the dispenser until the water
runs clear (approx. 6-7 minutes). This will clean the
water supply system and remove air from the lines.
water supply system and remove air from the lines.
3. Additional fl ushing may be required in some
households.
4. Open the Refrigerator door and make sure there
are no water leaks coming from the water fi lter.
Be sure to fl ush the dispenser thoroughly or
water may leak from it. This is due to the fact
water may leak from it. This is due to the fact
that there is still air in the line.
Plastic tubing
(Supplied)
Ferrule
(Not supplied)
Compression nut
(6.35 mm) (Supplied)
(6.35 mm) (Supplied)
Compression fitting
(Supplied)
(Supplied)
Bulb
Compression nut
(6.35 mm)
(Not supplied)
(6.35 mm)
(Not supplied)
Copper tubing
or
Plastic tubing
(Not supplied)
(Not supplied)
Household water line
Refrigerator
Refrigerator
1
2
3
Sticker
(month indicator)
(month indicator)
• 6.35 mm compression nut • copper tubing
• plastic tubing
• ferrule
Turn until
the label is
aligned.
the label is
aligned.
Separation
of red cap.
of red cap.
Cover fi lter
4
5
DA99-03403B-17.indb 19
DA99-03403B-17.indb 19
2016. 3. 24.
10:02
2016. 3. 24.
10:02