Yamaha 007POTO-G0 Manuel D’Utilisation
73
Sending signals from MIX channels to the STEREO/MONO bus
6
Output channel oper
ations
LS9-16/32 Owner’s Manual
9
If you want to use the MONO bus, make
sure that the [ON] key of the MONO channel
is turned on, and raise the fader of the
MONO channel to an appropriate position.
sure that the [ON] key of the MONO channel
is turned on, and raise the fader of the
MONO channel to an appropriate position.
This operation will differ between the LS9-16 and
LS9-32.
LS9-32.
●
For the LS9-16
Assign the MONO channel to the custom fader layer,
press the LAYER [CUSTOM] key to access the cus-
tom fader layer, and then operate the [ON] key and
fader of the corresponding channel module.
press the LAYER [CUSTOM] key to access the cus-
tom fader layer, and then operate the [ON] key and
fader of the corresponding channel module.
●
For the LS9-32
Press the LAYER [MASTER] key to access the master
fader layer, and operate the [ON] key and fader of
channel module 32.
fader layer, and operate the [ON] key and fader of
channel module 32.
10
Select the master fader layer, make sure
that the [ON] key of the desired MIX channel
is turned on, and raise the fader to an
appropriate position.
that the [ON] key of the desired MIX channel
is turned on, and raise the fader to an
appropriate position.
● For a MIX channel set to ST/MONO
mode
11
Use the ST button and MONO button in the
TO STEREO/MONO popup window as on/off
switches for the signal sent from the MIX
channel to the STEREO bus and MONO
bus.
TO STEREO/MONO popup window as on/off
switches for the signal sent from the MIX
channel to the STEREO bus and MONO
bus.
12
Use the SELECTED CHANNEL section
[PAN] encoder to adjust the pan/balance of
the signal sent from the MIX channel to the
STEREO bus.
[PAN] encoder to adjust the pan/balance of
the signal sent from the MIX channel to the
STEREO bus.
You can obtain the same result by using the TO ST
PAN/TO ST BALANCE knob in the TO STEREO/
MONO popup window.
PAN/TO ST BALANCE knob in the TO STEREO/
MONO popup window.
● For a MIX channel set to LCR mode
11
Use the LCR button in the TO STEREO/
MONO popup window as an on/off switch
for the signal sent from the MIX channel to
the STEREO bus and MONO bus.
MONO popup window as an on/off switch
for the signal sent from the MIX channel to
the STEREO bus and MONO bus.
For a MIX channel that is set to LCR mode, the signal
sent to the STEREO bus and MONO bus can be
switched on/off in a single operation.
sent to the STEREO bus and MONO bus can be
switched on/off in a single operation.
12
Use the CSR knob in the TO STEREO/MONO
popup window to adjust the proportion
between the signal level sent from that MIX
channel to the STEREO (L/R) bus and the
signal level sent to the MONO (C) bus.
popup window to adjust the proportion
between the signal level sent from that MIX
channel to the STEREO (L/R) bus and the
signal level sent to the MONO (C) bus.
13
Use the TO ST PAN knob in the TO STEREO/
MONO popup window to set the panning of
the signal sent from the MIX channel to the
STEREO (L/R) bus and the MONO (C) bus.
MONO popup window to set the panning of
the signal sent from the MIX channel to the
STEREO (L/R) bus and the MONO (C) bus.
If the CSR knob is set to 0%, operating the TO ST
PAN knob of a MIX channel will change the signal
levels sent to the STEREO (L/R) bus and MONO (C)
bus as shown in the following illustration. In this case,
the TO ST PAN knob will operate as a conventional
PAN knob, and no signal is sent to the MONO (C) bus.
PAN knob of a MIX channel will change the signal
levels sent to the STEREO (L/R) bus and MONO (C)
bus as shown in the following illustration. In this case,
the TO ST PAN knob will operate as a conventional
PAN knob, and no signal is sent to the MONO (C) bus.
If a MIX channel set to stereo is selected, operating
the TO ST BALANCE knob will change the signal
levels sent from the MIX channel to the STEREO (L/
R) bus and MONO (C) bus as shown in the following
illustration. In this case, the [PAN] encoder will oper-
ate as a conventional BALANCE knob, and no signal
is sent to the MONO (C) bus.
the TO ST BALANCE knob will change the signal
levels sent from the MIX channel to the STEREO (L/
R) bus and MONO (C) bus as shown in the following
illustration. In this case, the [PAN] encoder will oper-
ate as a conventional BALANCE knob, and no signal
is sent to the MONO (C) bus.
The following steps will differ depending on whether
you selected a ST/MONO mode MIX channel or an
LCR mode MIX channel in step 6.
you selected a ST/MONO mode MIX channel or an
LCR mode MIX channel in step 6.
C
L
R
TO ST PAN knob
Signal sent to the
STEREO (L) bus
STEREO (L) bus
Signal sent to the
STEREO (R) bus
STEREO (R) bus
Signal le
vel
C
L
R
TO ST BALANCE knob
Signal sent from the
odd-numbered MIX
channel to the STE-
REO (L) bus
odd-numbered MIX
channel to the STE-
REO (L) bus
C
L
R
TO ST BALANCE knob
Signal sent from the
even-numbered MIX
channel to the STE-
REO (R) bus
even-numbered MIX
channel to the STE-
REO (R) bus
Signal le
vel
Signal le
vel