Maytag mah22pdagw0 Manuel D’Utilisation
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
■
Pliers (that open to
39.5 mm [1
39.5 mm [1
9
/
16
"])
■
Flashlight (optional)
Tools needed for installation
■
Open end wrenches
1
/
2
" and
9
/
16
"
■
Torx
®†
T-20 Security
screwdriver
■
¼" nut driver
■
Level
■
Wood block
■
Ruler or measuring tape
†
® TORX is a registered trademark of Acument Intellectual Properties, LLC.
Parts supplied
A. U-shaped hose form
B. Water inlet hoses (2)
B. Water inlet hoses (2)
C. Inlet hose washers (4)
D. Transit bolt hole plug (4)
D. Transit bolt hole plug (4)
E. Beaded tie strap
A
B
C
D
E
Parts supplied for PD Models:
Service door lock cam
Foam pads
Parts supplied for PD Models:
■
Coin sensor white
■
Coin sensor black
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here contact your authorized
Maytag distributor.
in purchasing one of the items listed here contact your authorized
Maytag distributor.
If You Have
You Will Need to Buy
Laundry tub or
standpipe taller
than 2.4 m (96")
standpipe taller
than 2.4 m (96")
Sump pump system (if not already
available)
available)
Overhead sewer
Standard 76 L (20 gal. ), 762 mm (30") tall
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain
Siphon break, Part Number 285834;
additional drain hose,
additional drain hose,
Part Number 8318155; and connector
kit, Part Number 285835
kit, Part Number 285835
Drain hose
too short
1.2 m (4 ft.) drain hose extension kit,
Part Number 285863
Water taps beyond
reach of fill hoses
reach of fill hoses
2 longer water fill hoses:
1.8 m (6 ft.) Part Number 76314
3.0 m (10 ft.) Part Number 350008
Options
Pedestal
You have the option of purchasing pedestals separately for this
washer. The pedestal will add to the total height of the washer.
washer. The pedestal will add to the total height of the washer.
Optional pedestal
Pedestal
Height
Approximate
height
height
with washer
Color
Model
Number
Number
(73 mm) 2
7
/
8
"
(1207 mm) 47.5"
White
WHP0400VW
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, or recessed area. See “Drain System.”
basement, laundry room, or recessed area. See “Drain System.”
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
considered. Proper installation is your responsibility.
You will need
■
A water heater set to deliver 60°C (140°F) water to the
washer.
washer.
■
An earthed electrical outlet located within 1.8 m (6 ft.) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■
Hot and cold water taps located within 1.2 m (4 ft.)
of the hot and cold water fill valves, and water pressure
of 137.9-689.6 kPa (20-100 psi).
■
A level floor with a maximum slope of 25 mm (1") under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
If You Have
You Will Need to Buy