Panasonic KXTCD200G Mode D’Emploi
Preparation
9
Battery life
After your Panasonic batteries are fully charged,
you can expect the following performance:
Ni-MH batteries (700 mAh)
After your Panasonic batteries are fully charged,
you can expect the following performance:
Ni-MH batteries (700 mAh)
Hinweis:
L
L
Actual battery performance depends on a
combination of how often the handset is in use
(talking) and how often it is not in use
(standby).
combination of how often the handset is in use
(talking) and how often it is not in use
(standby).
L
Battery operating time may be shortened over
time depending on usage conditions and
ambient temperature.
time depending on usage conditions and
ambient temperature.
Battery replacement
If 7 flashes even after the handset batteries
have been charged for 7 hours, the batteries
must be replaced.
Wichtig:
L
have been charged for 7 hours, the batteries
must be replaced.
Wichtig:
L
We recommend the use of Panasonic
rechargeable batteries noted on Seite 4. If you
install non-rechargeable batteries and start
charging, the batteries may leak electrolyte.
rechargeable batteries noted on Seite 4. If you
install non-rechargeable batteries and start
charging, the batteries may leak electrolyte.
L
Do not mix old and new batteries.
1
Press the notch on the handset cover firmly
and slide it in the direction of the arrow.
and slide it in the direction of the arrow.
2
Remove the old batteries positive (S)
terminal first and install the new ones. See
Seite 8 for battery installation.
terminal first and install the new ones. See
Seite 8 for battery installation.
Turning the power on/off
Power on
Press {ih} for about 1 second.
L
L
The display will change to the standby mode.
Power off
Press {ih} for about 2 seconds.
L
L
The display will go blank.
Setting the date and time
Wichtig:
L
L
Confirm that the AC adaptor is connected.
L
Ensure that w is not flashing.
1
Press {j/OK}.
2
Select “Mobilteileinst.”, then press
{>}
{>}
.
3
Select “Zeiteinstell.”, then press {>}.
4
Select “Datum/Uhr eing.”, then press
{>}
{>}
.
5
Enter the current day, month and year by
selecting 2 digits for each.
Beispiel: 17 May, 2005
Press {1}{7} {0}{5} {0}{5}.
selecting 2 digits for each.
Beispiel: 17 May, 2005
Press {1}{7} {0}{5} {0}{5}.
6
Enter the current hour and minute by
selecting 2 digits for each.
L
selecting 2 digits for each.
L
You can select “AM”, “PM” or 24-hour time
entry by pressing {*} repeatedly.
entry by pressing {*} repeatedly.
Beispiel: 3:30 PM
Press {0}{3} {3}{0}, then press {*}
repeatedly until “03:30 PM” is displayed.
Press {0}{3} {3}{0}, then press {*}
repeatedly until “03:30 PM” is displayed.
7
Press {j/OK}.
8
Press {ih}.
Hinweis:
L
L
To correct a digit, press {<} or {>} to move
the cursor, then make the correction.
the cursor, then make the correction.
L
The date and time may be incorrect after a
power failure. In this case, set the date and
time again.
power failure. In this case, set the date and
time again.
Operation
Operating time
While in use (talking)
20 hours max.
While not in use
(standby)
(standby)
170 hours max.
TCD200G(e-g).book Page 9 Tuesday, February 8, 2005 8:57 AM