Manualsbrain.com
  1. Manuels
  2. Marques
  3. Sena Technologies Inc.
  4. PARANISD1100
  5. Manuel D’Utilisation

Sena Technologies Inc. PARANISD1100 Manuel D’Utilisation

Télécharger
Page de 48
 13
2.7. Pairing Button 
 
Parani-SD1100 provides Pairing Button for instant configuration without a PC to make an automatic 
connection between two Parani-SD1100s. In this example we will refer to the two Parani-SD1100s as 
SD1 and SD2. (Only single connection mode) 
 
Step 1.
 Turn on SD1 and SD2 and reset both of them by pressing Factory Reset Button. 
Step 2.
 Press the Pairing Button of SD1 for 2 seconds until Mode LED blinks 3 times every 3 seconds. 
Keep the power ON. 
Step 3.
 Press the Pairing Button of SD2 for 2 seconds until Mode LED blinks 3 times every 3 seconds. 
Now press again the Pairing Button for 2 seconds until Mode LED blinks every second. 
Step 4.
 Wait for SD1 & SD2 to connect to each other until the Connect LED’s of SD1 and SD2 blink 
every 1 second. It takes about 10 seconds to make a connection. If there are many Bluetooth 
devices nearby, it may take longer. 
Step 5.
 Turn SD1 off and on. Mode LED blinks twice in green every 3 seconds. 
Step 6.
 Turn SD2 off and on. Mode LED blinks in green every second. 
Step 7.
 Now SD1 and SD2 are configured to make automatic connection to each other, whenever they 
are powered on. 
 
Using a pair of Parani-SD1100 in this fashion is similar to that of using a wireless serial cable. 
 
* Note: When using the pairing buttons, the Command Response option will be deactivated 
automatically. The Parani-SD1100 will not send the response messages such as OK, Connect and 
Disconnect.  
 
Table 2-8 Pairing Process by Pairing Button 
SD1 Status 
LED 
SD2 Status 
LED 
1. Factory reset 
Mode0 
Mode LED turns on 
1. Factory reset
Mode0 
Mode LED turns on 
2. Push pairing 
button 
Mode3  Mode LED blinks 3 
times every 3 seconds
2. Push pairing 
button 
Mode3 
Mode LED blinks 3 
times every 3 seconds
 
 
 
3. Push pairing 
button again 
Mode1  Mode LED blinks 
every second 
4. 
Connected 
Slave 
Connect LED blinks 
every second 
4. 
Connected 
Master 
Connect LED blinks 
every second 
 
Using pairing button, users can make a pairing connection between a Parani-SD unit and other 
Bluetooth devices. 
 
Step 1.
 Turn on SD1 and reset it by pressing Factory Reset Button. 
Step 2.
 Press the Pairing Button of SD1 for 2 seconds until Mode LED blinks 3 times every 3 seconds. 
Keep the power ON. 
Step 3.
 Users can discover and connect to SD1 by using the software or user interface of other   
Bluetooth device that they want to connect from. 
Step 4.
 When they are connected, the Connect LED of SD1 blinks every 1 second.   
Step 5.
 Turn off and on. Mode LED blinks twice in green every 3 seconds. 
Step 6.
 Now SD1 is waiting for a connection from the last connected Bluetooth device. The last   
connected Bluetooth device can connect to SD1. 
 
Table 2-9 Pairing Process with other Bluetooth device by Pairing Button 
SD1 
Status 
LED 
Other Bluetooth Device 
Status
1. Factory reset 
Mode0 
Mode LED turns on 
 
 
2. Push pairing button 
Mode3  Mode LED blinks 3 times 
every 3 seconds