SendFar Technology Co. Ltd. OAP-02002 Manuel D’Utilisation
4
and set the terminal to 15200 Baud, No-Parity, 8 data bits, 1 Stop bit, and
ANSI compatible.
NOTE: This connection is required for setting up initial configuration
information.
After configuration is completed, this cable may be removed until additional
configuration is required via the Serial Port.
ANSI compatible.
NOTE: This connection is required for setting up initial configuration
information.
After configuration is completed, this cable may be removed until additional
configuration is required via the Serial Port.
1.5 Connecting the power supply and Ethernet
cable
cable
Step 3
Plug the female end of the power cord into the Inline Power Injector,
and then plug the male end of the power cord into a power outlet or power
strip. The Power LED on the front of the Inline Power Injector will light up.
strip. The Power LED on the front of the Inline Power Injector will light up.
Step 4
Run the cross over Ethernet cable (included in your package) from
Data Input Port (on the front of the Inline Power Injector) to the Ethernet
Port on the PC we mentioned above.
Port on the PC we mentioned above.
NOTE: This connection is required for setting up initial configuration
information. After configuration is completed, this cable will be removed,
and then you should run an Ethernet cable from Data Input Port (on the
front of the Inline Power Injector) to the LAN connection (such as a hub or
concentrator).
information. After configuration is completed, this cable will be removed,
and then you should run an Ethernet cable from Data Input Port (on the
front of the Inline Power Injector) to the LAN connection (such as a hub or
concentrator).
Step 5
Plug the MIL-C-5015 style Ethernet connector into the Special
Ethernet port on the back of the access point.
Step 6
Plug the RJ-45 Ethernet connector (the other end of the Special
Ethernet cable) into the Power & Data Output Port on the front of the Inline
Power Injector. When the Access Point receives power over the Ethernet
cable, the Access Point will start its boot sequence and the Active LED on
the front of the Inline Power Injector will light up.
Power Injector. When the Access Point receives power over the Ethernet
cable, the Access Point will start its boot sequence and the Active LED on
the front of the Inline Power Injector will light up.
5
1.6 Outdoor
Installation
Outdoor Access Point device can be mounted on the side of a
building or mounted to an mast as shown in following:
building or mounted to an mast as shown in following:
A wall (side) mount allows for mounting the Outdoor AP on the side of
a building. This will provide a convenient mounting location when the
roof overhang is not excessive and/or the location is high enough to
provide a clear line of sight.
a building. This will provide a convenient mounting location when the
roof overhang is not excessive and/or the location is high enough to
provide a clear line of sight.
Grounding
A safety grounding system is necessary to protect your outdoor
installation from lightning strikes and the build-up of static electricity.
So direct grounding of the antenna mast, Outdoor AP and
Surge Arrester is very important. And so mounting the Outdoor AP on
the antenna mast, you have to connect the Outdoor AP to the same
grounding system with the AC wall outlet.
The grounding system must comply with the National Electrical Code
and safety standards that apply in your country. Always check with a
qualified electrician if you are in doubt as to whether your outdoor
installation is properly grounded.
installation from lightning strikes and the build-up of static electricity.
So direct grounding of the antenna mast, Outdoor AP and
Surge Arrester is very important. And so mounting the Outdoor AP on
the antenna mast, you have to connect the Outdoor AP to the same
grounding system with the AC wall outlet.
The grounding system must comply with the National Electrical Code
and safety standards that apply in your country. Always check with a
qualified electrician if you are in doubt as to whether your outdoor
installation is properly grounded.