Redline Communications Inc. AN80IA Manuel D’Utilisation
Red
CONNEX
TM
AN-80i
PMP
User Manual
70-00072-01-03
Proprietary Redline Communications © 2007
March 19, 2007
Page 51 of 60
5.4
Troubleshooting the Web Interface
The following table lists some common troubleshooting tips for the web interface.
Table 22: Diag. - Web Interface Diagnostics
Symptom
Possible
Problem
Problem
Solution
Incorrect IP
address and/or
subnet mask.
address and/or
subnet mask.
Perform a ping test from the host computer
command line.
If the ping test is unsuccessful, then the problem
is with the IP address. Perform a long reset to
apply the default address (192.168.25.2) and
Subnet Mask (255.255.255.0)
command line.
If the ping test is unsuccessful, then the problem
is with the IP address. Perform a long reset to
apply the default address (192.168.25.2) and
Subnet Mask (255.255.255.0)
Problems with
host computer, or
AN-80i.
host computer, or
AN-80i.
If the ping is successful, reset the AN-80i, and/or
reset the host computer.
reset the host computer.
General
Information
screen is not
displayed
Information
screen is not
displayed
Host PC ARP
table is
incorrectly
configured
table is
incorrectly
configured
Run 'arp -d' whenever the AN-80i is swapped.
Check that the subnet mask for the host PC
matches the subnet mask of the AN-80i. Check
that the host PC's address is 192.168.25.n,
where 'n' is not equal to 0,2, or 255.
Check that the subnet mask for the host PC
matches the subnet mask of the AN-80i. Check
that the host PC's address is 192.168.25.n,
where 'n' is not equal to 0,2, or 255.
Attempt to login to the AN-80i using a Web browser. Microsoft Internet Explorer is
recommended. If the AN-80i does not respond by displaying the login dialog box, check
that the correct IP address is being used. The value 192.168.25.2 is the factory default
value and may have been changed during installation.
Test is to verify the IP address is reachable from the computer. Use the ping command to
test the connection between the AN-80i and host computer.
recommended. If the AN-80i does not respond by displaying the login dialog box, check
that the correct IP address is being used. The value 192.168.25.2 is the factory default
value and may have been changed during installation.
Test is to verify the IP address is reachable from the computer. Use the ping command to
test the connection between the AN-80i and host computer.
>ping 192.168.25.2
If the ping test is successful, the host computer was able to send and receive packets
to/from the AN-80i. The problem may be with the Internet browser or related settings on
the host computer. Reboot the host computer to try to resolve the problem.
If the ping is unsuccessful, there may be problems using that IP address; the IP address
may be incorrect, or there may be a duplicate address. For correct operation the host
computer and the AN-80i must be on the same subnet. For example, if the AN-80i is
using the factory default settings, the host computer could be set for an IP of
192.168.25.3 and a subnet mask of 255.255.255.0.
If the correct IP address of the AN-80i cannot be determined, it is recommended to
perform the IP recovery procedure. See 5.2: Procedure to Reset AN-80i IP Address on
page 49.
to/from the AN-80i. The problem may be with the Internet browser or related settings on
the host computer. Reboot the host computer to try to resolve the problem.
If the ping is unsuccessful, there may be problems using that IP address; the IP address
may be incorrect, or there may be a duplicate address. For correct operation the host
computer and the AN-80i must be on the same subnet. For example, if the AN-80i is
using the factory default settings, the host computer could be set for an IP of
192.168.25.3 and a subnet mask of 255.255.255.0.
If the correct IP address of the AN-80i cannot be determined, it is recommended to
perform the IP recovery procedure. See 5.2: Procedure to Reset AN-80i IP Address on
page 49.