Lutron Electronics Company Inc 0030 Manuel D’Utilisation
2
RadioTouch Tabletop Transmitter Addendum
Hardware Installation
RadioTouch
RadioTouch
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CLASS 2 LOW VOLTAGE WIRING
1 2 3 4 5
Power Status Program
Burn-In
1 2 3
Sivoia Cntrl 1
Sivoia Cntrl 2
RTA-RX-F-SC
Radio Frequency Controller
LISTED 243C
Ind. Cont. Eq.
Ind. Cont. Eq.
Coopersburg, PA 18036
STATUS INDICATOR OPERATION
ON - Burn-in Mode
Slow Blink -Normal Operation Mode
Fast Blink - Program Mode
Very Fast Blink - Receiving RF Data
ON - Burn-in Mode
Slow Blink -Normal Operation Mode
Fast Blink - Program Mode
Very Fast Blink - Receiving RF Data
RadioTouch
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Occ. Com
Signal
15V
24V
Circuit Com
Sw Closure 1
Sw Closure 2
Sw Closure 3
Sw Closure 4
Sw Closure 5
Closure Com
0-10 Purple
0-10 Gray
Receiver
Settings
Settings
T
erminal connections
are Class 2.
TM
Occ. Sensor
0-10 V Shade
Switch Closures
1 2 3 4 5
Powered
When Lit
When Lit
Status
Indicator
Indicator
Program
Button
Button
Burn-in
Button
Button
RECEIVER SWITCH SETTINGS
1. UP-Preset Lock
1. UP-Preset Lock
DN.-Preset Adj.
2. UP-Occ. Sensor
DN.-Emerg. Set.
3. UP-FDB Mode
DN.-ECO Mode
4. UP-OFF
DN.-Min. Light
5. UP-Auto ON
DN.-Manual ON
See Installers Guide for System
Addressing and Programming Instructions
Addressing and Programming Instructions
®
1 2 3
Shade
Settings
Settings
SHADE SWITCH SETTINGS
1. UP-A/C Shades
1. UP-A/C Shades
DN.-Normal Oper.
PS Signal
© 2000-2002 Lutron Electronics Co., Inc.
Addressing a Tabletop Transmitter
Each column of buttons on the tabletop transmitter
must be addressed to the Controller that you wish to
control with that column.
must be addressed to the Controller that you wish to
control with that column.
Addressing Columns of Buttons
Step A - Press and release the programming button on
the Controller. After the button is pressed the lights will
cycle up and down for 3 seconds to notify you that you
are in programming mode, and settle at 50% light
output. If you are using an RTA-RX-SW the lights will
cycle OFF and ON. The Status LED will be in fast blink
mode.
the Controller. After the button is pressed the lights will
cycle up and down for 3 seconds to notify you that you
are in programming mode, and settle at 50% light
output. If you are using an RTA-RX-SW the lights will
cycle OFF and ON. The Status LED will be in fast blink
mode.
Press and hold
this button
this button
Step B - While in programming mode press the
corresponding button in the column that you want to
control the receiver and hold for 5 seconds (see
Transmitter diagrams below). The Controller will flash
or cycle the lights OFF and ON when the transmitter is
added. If no lights are being controlled by the receiver,
you will not get visual feedback.
corresponding button in the column that you want to
control the receiver and hold for 5 seconds (see
Transmitter diagrams below). The Controller will flash
or cycle the lights OFF and ON when the transmitter is
added. If no lights are being controlled by the receiver,
you will not get visual feedback.
Step C - Press the programming button again to exit
from programming mode. The lights will go to high end
and the Status LED will return to slow blink mode. If
you are using an RTA-RX-SW the lights will cycle OFF
and ON. To test the tabletop transmitter for lights, press
any button in the column added on the tabletop
transmitter and verify that the lights respond. For
Sivoia
from programming mode. The lights will go to high end
and the Status LED will return to slow blink mode. If
you are using an RTA-RX-SW the lights will cycle OFF
and ON. To test the tabletop transmitter for lights, press
any button in the column added on the tabletop
transmitter and verify that the lights respond. For
Sivoia
®
shades, press any button and see that the
shades move. If no response return to step A and be
sure to hold the buttons for 5 seconds while in step B.
sure to hold the buttons for 5 seconds while in step B.
Step D - Repeat steps A through C for each column
you need to address to a Controller.
you need to address to a Controller.
Programming button
Status LED
Step A & C
Press and hold
this button
this button
Press and hold
this button
this button
Step B - Columns of buttons
Two button Switch Closure
Three button Switch Closure
Dimmable Lights
Non-dim Lights
Four button Switch Closure
Five button Switch Closure