Advance Security Inc TR06AM Manuel D’Utilisation
MAY/23/ 2003
RST771IN
18
will report the new code three times with a one-second’s pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more then 5 seconds during
of above steps, the unit will revert back to the last successfully stored code. A [3] long chirps to confirm exit.
Will revert back to the last successfully stored code
Delete Password Pin Code / Override Without Password Pin Code (Factory default setting):
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more then 5 seconds during
of above steps, the unit will revert back to the last successfully stored code. A [3] long chirps to confirm exit.
Will revert back to the last successfully stored code
Delete Password Pin Code / Override Without Password Pin Code (Factory default setting):
Within 15 seconds, press and hold the transmitter
button for 3 seconds. A one long chirps to confirm
Deleted the Password Pin Code.
Example: To program the Password Code 92, you would;
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 6 times and hold it until three chirps with a long chirp is hearing then release the
Example: To program the Password Code 92, you would;
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 6 times and hold it until three chirps with a long chirp is hearing then release the
valet switch. You are now in the Alarm feature ‘III’ programming mode.
Program:
1. Press and release the transmitter
button once, [2] LED flash, [2] siren/horn chirp to indicate your are in
features “Password pin code programming mode”.
2. Within 5 seconds, press and release the valet Switch 9 times.
3. Within 15 seconds of the last entered 9ths digit, Turn the Ignition Switch to “ON” position.
4. Within 15 seconds press the valet Switch twice.
5. Turn the Ignition Switch to “OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be
repeated three times indicating the new code (92) has been accepted and stored in memory.
3. Within 15 seconds of the last entered 9ths digit, Turn the Ignition Switch to “ON” position.
4. Within 15 seconds press the valet Switch twice.
5. Turn the Ignition Switch to “OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be
repeated three times indicating the new code (92) has been accepted and stored in memory.
Exit
: Press any button (except
button) of the transmitter to exit the password pin set up mode. A 3 long
chirps & 3 parking light flashes to confirm exit.
REMOTE START FEATURE PROGRAM MODE.
START FEATURE “
I
” PRORAMMING:
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 8 times and hold it until four chirps with a long chirp is hearing then release the
2. Push the Valet switch 8 times and hold it until four chirps with a long chirp is hearing then release the
valet switch. You are now in the Start feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
LED two pulses
Three Chirps /
LED three pulses
LED three pulses
Four Chirps /
LED four pulses
LED four pulses
1
+
Gasoline Engine
Diesel Engine and
10 seconds warn-up
timer
10 seconds warn-up
timer
Diesel Engine and
15 seconds warn-up
timer
15 seconds warn-up
timer
Diesel Engine and
20 seconds warn-up
timer
20 seconds warn-up
timer
2
10 minutes run time
20 minutes run time
30 minutes run time
5 minutes run time
3
Factory alarm
disarm with channel
3 on
disarm with channel
3 on
Without this feature
4
Constant parking
light output
light output
Flashing parking
light output
light output
5
Door lock before
start
start
Door lock after
shut-down
shut-down
Door lock before
start and Door lock
after shut-down
start and Door lock
after shut-down
Without this feature
6
+
Press
-
button =
Activate Remote
Start.
Activate Remote
Start.
Press
+
button =
Activate Remote
Start.
Activate Remote
Start.
Press
button =
Activate Remote
Start.
Start.
7
+
H5/5 White / Blue
Wire =
1 pulse activate
Wire =
1 pulse activate
H5/5 White / Blue
Wire =
2 pulse activate
Wire =
2 pulse activate
H5/5 White / Blue
Wire =
3 pulse activate
Wire =
3 pulse activate
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.