Advance Security Inc TR06AM Manuel D’Utilisation

MAY/23/ 2003 

RST771IN 

19 

 
SAFE START (Child safety mode) 

Factory defaults setting to press the 

  button twice to start the vehicle.   

Programming this feature to eliminate an accidental remote start, when kids enter this transmitter, it requires: 

1.  The user press the transmitter 

  and 

  buttons at the same time to start the vehicle.   

     

1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.   
2. Push the Valet switch 10 times and hold it until five chirps with a long chirp is hearing then release the 

valet switch. You are now in the Start feature ‘II’ programming mode. 

3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.   
 

Press 
T

ransmitte

r 

Button 

One Chirp /   
LED one pulse 
Factory Default 
Setting 

Two Chirps /   
LED two pulses 
 

Three Chirps /   
LED three pulses 
 

Four Chirps /   
LED four pulses 
 

1 

 

Exit the programming mode. (3 long chirp & 3 parking light flashes to confirm this exit.) 

2 

 

 

 

Tachometer 
checking type.     

Voltage checking 
type 

Timer checking type 

 

RPM 

learning 

   

3 

 

Start Timer: 
0.6-second  

0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps), 
1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps), 
2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10 
chirps), 

 

Low check level 

Hi check level 

     

 

5 

 

-

 

 

Start or Stop the system for TESTING & ADJUSTMENT 

6 

 

+

 

   

“TEST” Mode for 
Zone 2 / instant 
trigger & Zone 3 / 
Door trigger   

“TEST” Mode for 
Zone 1 & Zone 4 (2 
Stage Shock 
Sensor)  

 

 

: Press the 

  button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit. 

Enter Start Feature ‘II’ Programming Mode: 
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.   
2. Push the Valet switch 10 times and hold it until five chirps with a long chirp is hearing then release the 

valet switch. You are now in the Start feature ‘II’ programming mode. 

3. Press and release the transmitter 

  and

 button at the same time once to set the “Tachometer 

Checking Type”. [1] LED flash, [1] chirp to Confirm this setting. 

4. Once you complete step 3, you can program “RPM Learning Mode” as below: 
 

While the system stay in Start Feature “II” programming mode, 

1. Press and release the transmitter 

  button once, [1] LED flash, [1] chirp to indicate your are in features 

“RPM Learning mode”.   

2. Start the vehicle with the key. (While the engine is running, the parking & LED will flash, If don’t, please 

check tachometer White/Red wire connection. (H5/8) 

3. Press and hold the valet switch for 2 seconds until a long chirp and the LED light constant for two seconds. 

The RPM signal is learned. 

4. Once you complete step 3, you can adjust and test “Check Level” as below: 
 

While the system stay in Start Feature “II” programming mode, 

1. Press the 

  button twice on the transmitter to start the vehicle. 

2. If everything goes well: