Advance Security Inc TR06AM Manuel D’Utilisation
MAY/23/ 2003
RST771IN
22
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
SHUTDOWN DIAGNOSTICS
The unit has the ability to report the cause of the last shutdown of the remote start system.
Enter:
Enter:
1.
Turn the Ignition 'switch to ‘ON position.
2.
Press the
button on the transmitter.
3.
The LED will now report the last system shutdown by flashing for one minute in the following grouped
patterns:
patterns:
LED
Flashes
Flashes
Shutdown Mode
2
(-) Safety Shutdown input (Hood) or
1. Close the hood.
2. Check H5/1 White/ Black wire connection.
2. Check H5/1 White/ Black wire connection.
2
(+) Safety Shutdown input (Brake) or
3. Check H5/2 White/ Violet wire connection.
2
Neutral Safety Switch input fail
4. Move the Enable Toggle Switch to “ON”
position. (If installed.)
5. Move the gear selector to “Park”/ “NEUTRAL”
position.
6. Check H5/3 Black/White wire connection.
position. (If installed.)
5. Move the gear selector to “Park”/ “NEUTRAL”
position.
6. Check H5/3 Black/White wire connection.
3
No RPM or
Low Voltage.
Low Voltage.
Tachometer Checking Type:
Check H5/8 White/Red wire connection
Voltage Checking Type:
Program the “CHECK LEVEL” from
“Hi Check Level” to “Low Check Level”
Check H5/8 White/Red wire connection
Voltage Checking Type:
Program the “CHECK LEVEL” from
“Hi Check Level” to “Low Check Level”
5
Over-rev
6
System timed out
7
Transmitter
8
Tach. Signal has not been learned
Re-learning the RPM (Start Feature
II
– 2 / 3)
9
The procedure of the Engine start
memorizing for the vehicle with
standard (manual) transmission gear is
not completed.
memorizing for the vehicle with
standard (manual) transmission gear is
not completed.
Check Operation Manual # Remote Start
Operation
B section.
Operation
B section.
TESTING YOUR INSTALLATION:
Caution!! The follow procedure must be performed after the installation of the Remote Start Device. It is the
responsibility of the installing technician to complete these tests. Failure to test the unit in the following
manner may result in personal injury, property damage, or both.
1. Test the BRAKE shutdown circuit: With the vehicle in park (P), start the vehicle using the remote
transmitter, Once the engine is running, press the brake pedal. The vehicle should shut down immediately.
If the vehicle continues to run, check the brake circuit WHITE/ VIOLET
If the vehicle continues to run, check the brake circuit WHITE/ VIOLET
wire (H5/2) connection.
2. Test the HOOD PIN shutdown circuit: Start the vehicle using the remote transmitter, Once the engine is
running, pull the hood release and raise the hood. The vehicle should shut down immediately. If the
vehicle continues to run, check the hood pin WHITE/ BLACK wire (H5/1) connection.
vehicle continues to run, check the hood pin WHITE/ BLACK wire (H5/1) connection.
3. NEUTRAL START SAFETY TEST:
1. Set the vehicle parking brake.
2. Block the drive wheels to prevent vehicle movement.
3. Sitting in the vehicle, turn the ignition switch to “ON” or “RUN” position. But do not start the engine.
4. Step on the brake pedal and shift the gear selector into “DRIVE” (D).
5. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut
2. Block the drive wheels to prevent vehicle movement.
3. Sitting in the vehicle, turn the ignition switch to “ON” or “RUN” position. But do not start the engine.
4. Step on the brake pedal and shift the gear selector into “DRIVE” (D).
5. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut
down the Remote Start Device.
6. Start the vehicle using remote transmitter.
a. If the starter does not engage, the test is complete.
b. If the starter engages, immediately step on the brake pedal to shut down the system, recheck your
b. If the starter engages, immediately step on the brake pedal to shut down the system, recheck your
VIOLET wire (H1/1 starter output wire) connection. The heavy gauge VIOLET wire must be
connected to the ignition switch side of the Neutral Start Switch. If the vehicle you are working on
does not have an Electrical Neutral Safety Switch, it will be necessary to reconfigure the Remote
connected to the ignition switch side of the Neutral Start Switch. If the vehicle you are working on
does not have an Electrical Neutral Safety Switch, it will be necessary to reconfigure the Remote