Advance Security Inc TR06AM Manuel D’Utilisation

MAY/23/ 2003 

RST771IN 

21 

3. Press the transmitter 

  and 

  button at the same time to set the “Timer Checking Type”. [3] LED flash, 

        [3] chirp to confirm this setting   
4. Once you complete step 3, you can adjust and test “Start Timer” as below: 

While the system stay in Start Feature “II” programming mode, 

1. Press the 

  button twice on the transmitter to start the vehicle.   

2. If everything goes well: 

a. Press the '

 button twice on the transmitter to stop engine running. You have been completed this 

programming successfully. 

b. Press 

  button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking 

light flashes for confirmation.   

3. If the crank time is too long, (Engine already successfully running, while still cranks): 

a. Press the 

  button twice on the transmitter to stop engine running. 

b. Press the 

  button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm 

this enter. (Decrease “Start Timer” is necessary.) 

c. Repeat the step1 – 4. 

4. If the crank time is too short, (Engine not running, while stops cranks): 

a. Press the 

  button twice on the transmitter to stop engine running. 

b. Press 

  button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm this 

enter. (Increase “Start Timer ” is necessary.) 

c. Repeat the step1 – 4. 

 

In this test mode, this system can test the Zone 2 (Instant ground trigger), the Zone 3 (Door trigger), and the 
Zone 1 & Zone 4 (2 stage shock sensor) sensitivity. The installer can save time to test the 2 stage shock 
sensor sensitivity and sensor without using the traditional arming/disarming procedures to test the sensors.   
Enter: 
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.   
2. Push the Valet switch 10 times and hold it until five chirps with a long chirp is hearing then release the 

valet switch. You are now in the Start feature ‘II’ programming mode. 

Press and release the transmitter 

  and 

  button at the same time once. [1] LED flash, [1] 

siren/horn chirp to indicate your are in Zone 2 / instant ground trigger and Zone 3 / Door trigger test 
mode. 

Trigger sensor 

Siren chirps 

Zone 2 / Instant Ground trigger (H5/4 Blue wire) 

2 

Zone 3 / Door trigger (H5/6 Green or H5/7 Violet wire) 

3 

b. Test the Zone 1 & Zone 4 / Two Stage Shock Sensor (Connected to H7 4 Pin Plug): 

Press and release the transmitter 

  and 

  button at the same time again. [2] LED flash, [2] 

siren/horn chirps to indicate your are in the shock sensor (connected to H7 4 pin plug) test mode. 
1. Activate the warn-away (first stage of the shock sensor / Zone 1), system will emit a short chirp. 
2. Activate the full alarm (second stage of the shock sensor / Zone 4), system will emit a long chirp. 
3. Continue to test the shock sensor until reach the proper sensitivity. 

 

1. Turn the ignition ON then OFF 3 TIMES and stay in OFF position. 
2. Push the Valet switch 12 times and hold it until six chirp with a long chirp is hearing then release the valet 

switch. You are now in the “Return To Factory Default Setting” programming mode. 

3. Press and hold the 

 

and

  button at the same time on the transmitter for 6 seconds, there will be a 

confirmation six chirp with 3 long chirp to confirm the system “Alarm Feature I & II & III Programming all 
returns to factory default setting. 

4. Press  the 

 

first, within 3 seconds press and hold the 

 

and

 button at the same time on the 

transmitter for 6 seconds, there will be a confirmation six chirp with 3 long chirp to confirm the system 
“Start Feature I & II Programming all returns to factory default setting.