Tyco Safety Products/Sensormatic IDX8000NA Manuel D’Utilisation
PRELIMINARY
IDX-8000 Reader Sensor Network
Appliance
Appliance
Quick Start Guide
Introduction
This guide provides overview information for the IDX-8000; which includes the
following models and part numbers:
following models and part numbers:
IDX-8000-NA
IDX-8000-EU
The reader is shipped with these items:
Reader with mounting brackets
Power supply
Localized power cord
USB cable
IDX-8000 Reader Sensor Network Appliance Quick Start Guide
Document of Conformity(-EU version only)
The IDX-8000 Quick Start Guide includes LED definitions, port descriptions,
connection and mounting information, as well as regulatory and compliance
information. References to IDX-8000 apply to all versions, except where the
version is explicitly identified.
connection and mounting information, as well as regulatory and compliance
information. References to IDX-8000 apply to all versions, except where the
version is explicitly identified.
This device received all regulatory approvals under the name Sensormatic
Electronics, LLC.
Electronics, LLC.
8200-2697-12, Rev. 1.0b
RF Connections
Port
Description
RF Outputs 1
–8
Monostatic RF output ports (Reverse Polarity-SMA)
Digital Connections
Port
Description
Power
24Vdc
24Vdc
Power supply port. Connect the power supply provided with the
reader.
reader.
Power consumption: 24W maximum.
Ethernet 2
PoE*
PoE*
10/100 Auto MDI/MDI-X Ethernet port. The RJ-45 Ethernet jack
supports either a standard or cross over cable. The Ethernet 1 and
Ethernet 2 ports act like a network switch.
supports either a standard or cross over cable. The Ethernet 1 and
Ethernet 2 ports act like a network switch.
PoE (Power over Ethernet) IEEE 802.3at (802.3af with some power
limitations).
limitations).
Ethernet 1* 10/100 Auto MDI/MDI-X Ethernet port. The RJ-45 Ethernet jack
supports either a standard or cross over cable. The Ethernet 1 and
Ethernet 2 ports act like a network switch.
Ethernet 2 ports act like a network switch.
USB A Host USB 2.0 Standard Series A port supports standard USB
peripherals.
USB B
Device
Device
USB 2.0 Standard Series B port supports Ethernet over USB.
Self-powered device; no host current required.
RS-485 2*
For future use (RJ-45 connector).
RS-485 1*
For future use (RJ-45 connector).
GPIO /
RS-232
RS-232
General Purpose Input/Output (15 pin) port. Supports a HD-15
cable assembly for connection to external devices.
cable assembly for connection to external devices.
RS-232 serial port for future use.
Reset
The Reset button restores the reader with custom settings or to its
factory default settings.
factory default settings.
* Connect Ethernet and RS-485 cables with care. The Ethernet and RS-485
connectors both use RJ-45 plugs.
LED Definitions
See the illustrations for the LED positions on the IDX-8000.
LED
State
Description
Power
Solid green
Power is on and unit is ready.
Off
No power to the unit.
Solid yellow
Unit is powering on.
Status
Off
Operational, not under LLRP management.
Solid yellow
Power LED yellow: unit is powering on.
Power LED green: unit is in power save mode.
Blinking yellow
Software is being downloaded.
Solid green
Under LLRP management. All other states take
precedence.
precedence.
Solid red
Error detected / self-test failed.
Tag
Green flash
Valid tag is being read.
Yellow flash
Tag below RSSI threshold.
RF Status Yellow
Transmitter is active.
Off
Transmitter is not active.
Three yellow
blinks
blinks
Communication has been established with a
1-Wire device.
1-Wire device.
All LEDs self-test on power cycle.
Mounting
Position the IDX-8000 on the wall or shelf, ensuring a minimum clearance of 10cm
(4in) on all sides. The mounting brackets are reversible to meet a range of
installation requirements as shown below. Mark the hole locations using the
mounting bracket as a guide.
(4in) on all sides. The mounting brackets are reversible to meet a range of
installation requirements as shown below. Mark the hole locations using the
mounting bracket as a guide.
Remove the IDX-8000 and drill four mounting holes at the marked locations.
Reposition the IDX-8000 over the mounting holes and secure using fasteners
appropriate for its 0.5kg (1.1 lb) weight, the mounting surface, and any other
conditions present, such as vibration.
Reposition the IDX-8000 over the mounting holes and secure using fasteners
appropriate for its 0.5kg (1.1 lb) weight, the mounting surface, and any other
conditions present, such as vibration.
CAUTION: Observe the minimum radius specified for the associated
antenna when the cable must change direction. A crushed or kinked
antenna cable may impair reader performance.
antenna when the cable must change direction. A crushed or kinked
antenna cable may impair reader performance.
200mm (7.9in)
1
7
4
.3
m
m
(
6
.9
in
)
Power LED
Status LED
Tag LED
200mm (7.9in)
2
0
0
m
m
(
7
.9
in
)
RF Status LEDs
RF1
RF2
RF3
RF4
RF5
RF6
RF7
RF8
Power
24Vdc
24Vdc
Ethernet
1
GPIO /
RS-232
Ethernet
2 PoE
1 2
RS-485
RS-485
USB B
Device
Device
USB A
Host
Reset