3Com Corporation WL306 Manuel D’Utilisation
Selecting A Different Antenna
11
Selecting A Different
Antenna
Antenna
The standard detachable portable antenna supplied with the access point is a
multi-purpose antenna suitable for a variety of environments, including office
LANs, physical plants, and factory floors. If your site has special requirements that
might be served by different types of antenna, four optional antenna models are
available, as shown below:
multi-purpose antenna suitable for a variety of environments, including office
LANs, physical plants, and factory floors. If your site has special requirements that
might be served by different types of antenna, four optional antenna models are
available, as shown below:
You can order any of the optional antennas by model number from the 3Com
Web site.
Web site.
Omnidirectional Antenna
The fiberglass omnidirectional
antenna (model number 3CWE490)
is designed for use in harsh indoor
environments. It can be centrally
located on the ceiling to provide
uniform coverage over a wide area.
antenna (model number 3CWE490)
is designed for use in harsh indoor
environments. It can be centrally
located on the ceiling to provide
uniform coverage over a wide area.
This antenna features a built-in
matching network that eliminates
the need for a ground plane.
matching network that eliminates
the need for a ground plane.
This antenna can be mounted on
the ceiling by means of a standard
ceiling-mount bracket. Before
installing, ensure that access is
available for cable routing.
the ceiling by means of a standard
ceiling-mount bracket. Before
installing, ensure that access is
available for cable routing.
This antenna does not have an electrical connection between the mask mount and
the coaxial cable shield. However, adding a lightning arrestor will correct this
situation by grounding the outer shield as recommended. Some arrestor designs
provide over-voltage protection for the signal sent down the cable. If you use such
a design, be sure that it can pass signals used in the 2.5 GHz signal range. Many
inexpensive units are available with F connectors, but these are typically designed
the coaxial cable shield. However, adding a lightning arrestor will correct this
situation by grounding the outer shield as recommended. Some arrestor designs
provide over-voltage protection for the signal sent down the cable. If you use such
a design, be sure that it can pass signals used in the 2.5 GHz signal range. Many
inexpensive units are available with F connectors, but these are typically designed
Model number
3CWE490
3CWE492
3CWE497
3CWE498
3CWE495
3CWE496
Design and type
Omnidirectional
(fiberglass)
(fiberglass)
Ceiling-mount
omnidirectional
omnidirectional
Ceiling-mount
hallway
hallway
Directional Panel
(indoor/outdoor)
(indoor/outdoor)
Directional Panel
(outdoor)
(outdoor)
Directional Panel
(outdoor)
(outdoor)
Frequency Range 2.400-2.4835
GHz
2300-2500 MHz 2300-2500 MHz 2300-2500 MHz 2300-2500 MHz 2300-2500 MHz
Gain
4 dBi
2.5 dBi
4 dBi
8 dBi
13 dBi
18 dBi
VSWR across
band
band
< 1.5:1
< 1.35:1
< 1.5:1
< 1.5:1
< 1.3:1
< 1.5:1
Max Power Input 20 W
50 W
10 W
20 W
20 W
20 W
Temperature
range
range
-40
°
C to +80
°
C
-40
°
C to +80
°
C
-40
°
C to +71
°
C
-40
°
C to +80
°
C
-51
°
C to +71
°
C
-51
°
C to +71
°
C
Dimensions
(inches)
(inches)
10” (height)
4.25 (diameter)
2.6 x 1.8 x 0.2
5.1 x 4.7 x 1.5
8.7 x 7.9 x 1.4
14.7 x 13.5 x 1.5
Weight
5.34 oz.
8 oz.
2 oz.
8 oz.
12.32 oz.
36.8 oz.
Cable
A six-foot accessory cable (model 3CWE480) is required for each of these optional antennas. It provides the
transition from the SMA connector on the access point to the N-type connector on the antenna. A 20-foot
cable (model 3CWE481) and a 50-foot cable (model 3CWE482) are also available.
transition from the SMA connector on the access point to the N-type connector on the antenna. A 20-foot
cable (model 3CWE481) and a 50-foot cable (model 3CWE482) are also available.