3M Company OPTICOMGPS1 Manuel D’Utilisation
Vehicle Equipment Installation Instructions
19
6 Checkout
This section describes how to check out and
test the installed 3M™ Opticom™ GPS
Priority Control System.
test the installed 3M™ Opticom™ GPS
Priority Control System.
6.1 Configuration Setup and Checkout
Using the Vehicle Configuration window of the ITS
Explorer application, configure the vehicle control unit
with the following parameters: (See the on-line Help
files and the Operation Manual for additional
information.)
Explorer application, configure the vehicle control unit
with the following parameters: (See the on-line Help
files and the Operation Manual for additional
information.)
Using the General Configuration window, set the
following parameters:
following parameters:
Configuration
??
Vehicle Name
Up to 40 alphanumeric characters
Up to 40 alphanumeric characters
??
Agency ID
1 – 254
1 – 254
??
Vehicle Class
1 – 15
1 – 15
??
Vehicle ID
1 – 9999
1 – 9999
Operating Mode
??
Disable Mode
Latching or Non-Latching
Latching or Non-Latching
??
Disable Trigger method
+12 VDC to Ground
Ground to +12 VDC
+12 VDC to Ground
Ground to +12 VDC
6.2 Input Verification
1. Open the Vehicle Configuration window in ITS
Explorer.
2. Using the Diagnostic Activity window, open the View
Inputs Sensing window and activate the left turn
signal followed by the right turn signal. Verify that
the vehicle equipment detects each input.
signal followed by the right turn signal. Verify that
the vehicle equipment detects each input.
If both signals are being detected when only the left
or right signal is activated, it may be necessary to
connect the turn signal line to another point.
or right signal is activated, it may be necessary to
connect the turn signal line to another point.
3. Activate the disable switch and verify that the vehicle
equipment detects this action. Also observe the
DISABLE indicator and the ON/OFF switch
indicator. Both indicators will be flashing green when
the disable switch is activated. See Table 6-1.
DISABLE indicator and the ON/OFF switch
indicator. Both indicators will be flashing green when
the disable switch is activated. See Table 6-1.
4. Verify that Disable mode activation is correct.
If Latching Disable mode is used, the vehicle control
unit stays in Disable mode after the disable switch is
returned to its normal state. Turning the vehicle
control unit off for a few seconds and then back on
removes the Disable mode.
unit stays in Disable mode after the disable switch is
returned to its normal state. Turning the vehicle
control unit off for a few seconds and then back on
removes the Disable mode.
If Non-Latching Disable mode is used, the vehicle
control unit removes the Disable mode as soon as
the disable switch is returned to its normal state.
control unit removes the Disable mode as soon as
the disable switch is returned to its normal state.
Table 6-1. Vehicle Control Unit Indicators
Indicator
Color or
Condition
Condition
Meaning
POWER
Green
Power applied to unit
ON/OFF
Switch
Switch
Green
Flashing
Green
Green
Power applied to unit
Vehicle in Disable mode
DISABLE
Off
Flashing
Green
Green
Vehicle NOT in Disable
mode
mode
Vehicle in Disable mode
GPS
Amber
Green
Not receiving GPS, radio
not transmitting
not transmitting
GPS has good 3D fix
RADIO
Amber
Green
No communication
between radio/GPS unit
and vehicle control unit
between radio/GPS unit
and vehicle control unit
Good communication
between radio/GPS unit
and vehicle control unit
between radio/GPS unit
and vehicle control unit
6.3 Performance Tests
WARNING
A completed installation that is not tested may
result in improper system operation, which may
result in accidents and/or injuries. To avoid
this problem, test the system to verify
proper operation. Improper system operation
may result in unsafe driver action.
result in improper system operation, which may
result in accidents and/or injuries. To avoid
this problem, test the system to verify
proper operation. Improper system operation
may result in unsafe driver action.