Authinx Inc. 24110T Manuel D’Utilisation
9
8
Most users will store VCR codes under the VCR button,
DVD codes under DVD, etc. If (for example) you want to
store a VCR code under DVD, first follow the procedure
for Direct Code Entry (previous page), and press DVD in
step 2 of Direct Code Entry, then enter ANY VCR code in
step 3 of Direct Code Entry. Then follow the steps for
Code Search on the previous page. Note: If the device
does not have a CHANNEL UP button, use PLAY (VCR
only) or ON-OFF instead. Code Search starts from the
currently stored 4-digit number under that mode.
DVD codes under DVD, etc. If (for example) you want to
store a VCR code under DVD, first follow the procedure
for Direct Code Entry (previous page), and press DVD in
step 2 of Direct Code Entry, then enter ANY VCR code in
step 3 of Direct Code Entry. Then follow the steps for
Code Search on the previous page. Note: If the device
does not have a CHANNEL UP button, use PLAY (VCR
only) or ON-OFF instead. Code Search starts from the
currently stored 4-digit number under that mode.
Code Search, cont.
Code Identification Feature
The Code Identification Feature allows you to identify
the four digit library code stored under your device key.
For example, if you want to find out what 4-digit code is
stored under your TV device key, follow the six steps
below:
the four digit library code stored under your device key.
For example, if you want to find out what 4-digit code is
stored under your TV device key, follow the six steps
below:
1. Press and hold the SETUP button until the red
indicator stays on. Release the SETUP button.
2. Press and release the desired mode button (TV,
VCR, etc.). The red indicator blinks, then stays lit.
3. Press and release the SETUP button. The red
indicator blinks off.
4. To find the first digit for the code stored under the
mode key pressed in step 2, press each numeric key
from 0-9 in turn. When the red indicator blinks off
the number you pressed is the first digit for the code
you are searching for.
from 0-9 in turn. When the red indicator blinks off
the number you pressed is the first digit for the code
you are searching for.
5. To find the second digit, repeat step 4. This time
when the red indicator blinks off this is the second
digit.
digit.
6. Repeat step 4 to find the third and fourth digits.
Programming Combo Device Codes
Some Combo devices (e.g., TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device. For
example, if you have a TV/DVD Combo, you might need
to set up one code under the TV button to control the
TV part AND a separate code (under any other Mode
button) to control the DVD part.
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device. For
example, if you have a TV/DVD Combo, you might need
to set up one code under the TV button to control the
TV part AND a separate code (under any other Mode
button) to control the DVD part.
Controlling Combo Devices
Some Combo devices (e.g., TV/VCR, TV/DVD, DVD/
VCR, etc.) have separate buttons on the original remote
to select the part of the Combo device to be controlled.
For example, if your Combo device is a DVD/VCR then
its original remote might have separate DVD and VCR
buttons for selection of the Combo part you would
control. The equivalent button functions can be found
on your new remote by using the device Mode and
SETUP buttons.
VCR, etc.) have separate buttons on the original remote
to select the part of the Combo device to be controlled.
For example, if your Combo device is a DVD/VCR then
its original remote might have separate DVD and VCR
buttons for selection of the Combo part you would
control. The equivalent button functions can be found
on your new remote by using the device Mode and
SETUP buttons.
Referring to “Code Search” on page 7, setup a device
Mode (e.g., DVD) with the correct code for your Combo
device. Assuming the DVD/VCR Combo device is the
example and its code is programmed under DVD Mode,
press and hold the DVD Mode button for more than
one second to send the DVD button command. To send
the VCR button command, quickly press and release the
SETUP button followed by pressing and releasing the
DVD Mode button. This method can be applied
similarly to all Combo devices (e.g., TV/VCR, TV/DVD,
DVD/VCR, etc.) and is available for all Modes. Note this
feature is not supported by all codes.
Mode (e.g., DVD) with the correct code for your Combo
device. Assuming the DVD/VCR Combo device is the
example and its code is programmed under DVD Mode,
press and hold the DVD Mode button for more than
one second to send the DVD button command. To send
the VCR button command, quickly press and release the
SETUP button followed by pressing and releasing the
DVD Mode button. This method can be applied
similarly to all Combo devices (e.g., TV/VCR, TV/DVD,
DVD/VCR, etc.) and is available for all Modes. Note this
feature is not supported by all codes.
Controlling Devices Requiring Separate Power On and
Off Buttons
Off Buttons
Some devices (e.g., certain RCA TVs) require separate
Power On and Power Off buttons to turn the device on
and off. The equivalent button functions can be found
on your new remote by using the device Mode and ON-
OFF buttons. Referring to “Code Search” on page 7,
setup a device Mode (e.g., TV) with the correct code for
your device.
Power On and Power Off buttons to turn the device on
and off. The equivalent button functions can be found
on your new remote by using the device Mode and ON-
OFF buttons. Referring to “Code Search” on page 7,
setup a device Mode (e.g., TV) with the correct code for
your device.
Assuming a TV device is the example and its code is
programmed under TV Mode, to turn your TV on, press
and hold the TV Mode button for more than one
second to transmit the Power On button command.
programmed under TV Mode, to turn your TV on, press
and hold the TV Mode button for more than one
second to transmit the Power On button command.
Setup, cont.