OnBoard Research Corporation FREEDOM-001 Manuel D’Utilisation

INTELLITOUCH FREEDOM ONE

MODEL NUMBER: WT1

This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to
operate the equipment.

NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15

of  the  FCC  Rules.  These  limits  are  designed  to  provide
reasonable  protection  against  harmful  interference  in  a
residential  installation.  This  equipment  generates,  uses  and

can  radiate  radio  frequency  energy  and,  if  not  installed  and
used  in  accordance  with  the  instructions,  may  cause  harmful
interference  to  radio  communications.  However,  there  is  no

guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:

—Reorient or relocate the receiving antenna.
—Increase  the  separation  between  the  equipment  and
receiver.

—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician

for help.

This Class B digital apparatus complies with Canadian ICES-

003.

Cet appareil numérique de la classe B est conforme à la

norme NMB-003 du Canada.

Power Requirements
The transmitter requires a single AAA battery.
The  pedal  requires  a  single  9v  battery  or
connection to a 9v DC supply (recommended).

Linking the Transmitter and Pedal
With both the transmitter and pedal turned on,
press  and  hold  the  “Set/Link”  button  on  the
rear  panel  of  the  pedal  for  3  seconds.  The
tuner will display a blinking letter “L”. Within
20  seconds,  press  and  hold  the  “Set/Link”
button  on  the  side  of  the  transmitter.    The
pedal will display a solid “L” for 3 seconds to
indicate that a link has been established. Once
a pedal/transmitter pair have been linked, they
should not need to be linked again.

Wireless Setup
Turn on the pedal and transmitter. Connect the
output  jack  of  the  Pedal  into  an  amplifier,
preamp,  effects  pedal,  mixer,  or  other
appropriate  equipment.      Plug  the  transmitter
into  the  instrument.  Turn  the  volume  on  the
instrument  to  its  maximum  level  for  best
results. Step on the pedal’s footswitch once to
mute the output and enable the tuner display.
Step  on  the  pedal’s  footswitch  again  to  un-
mute the output and disable the tuner display.

Wired Setup
Turn on the pedal. Connect the output jack of
the pedal to an amplifier, effects pedal, mixer,
or  other  appropriate  audio  equipment.
Connect an instrument to the input jack of the
pedal.  Step  on  the  pedal’s  footswitch  once  to
mute the output and enable the tuner display.

Step  on  the  pedal’s  footswitch  again  to  un-
mute the output and disable the tuner display.
Tuning Tips
- Turn instrument volume to the max level.
- Pluck single string with fingertip, not a pick.
- Mute strings that are not being tuned.

Transmitter LED Indication
- One flash every 2 seconds = Normal Use.
- Two flashes every 2 seconds = No Link.
- Solid yellow = Low Battery.

Specifications
Frequency: 2.404GHz – 2.476GHz
RF Transmit Power: 3.5dBm
Transmitter Battery: AAA Alkaline Battery(1)
Receiver Battery: 9V Alkaline Battery(1)
DC Power Connection: 8-12V DC 100mA
     (Center Ground, Case Positive)

For Best Results
- Do not use in areas with excessive WiFi
(IEEE 802.3) network access points.
- Turn the instrument volume up.
- Use new batteries for performance.

Limited Lifetime Warranty
For warranty details contact:
OnBoard Research Corporation
1321 Valwood Parkway, STE 440
Carrollton, TX, 75006

Email: Support@tuners.com
Web:

www.tuners.com

Phone: 1 (800) 340-8890

SET/

LINK

ADJ

PWR

9V DC

LINK

PWR

Pedal Rear Panel Diagram:

Transmitter Diagram: