OnBoard Research Corporation FREEDOM-001 用户手册
INTELLITOUCH FREEDOM ONE
MODEL NUMBER: WT1
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician
for help.
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Power Requirements
The transmitter requires a single AAA battery.
The pedal requires a single 9v battery or
connection to a 9v DC supply (recommended).
Linking the Transmitter and Pedal
With both the transmitter and pedal turned on,
press and hold the “Set/Link” button on the
rear panel of the pedal for 3 seconds. The
tuner will display a blinking letter “L”. Within
20 seconds, press and hold the “Set/Link”
button on the side of the transmitter. The
pedal will display a solid “L” for 3 seconds to
indicate that a link has been established. Once
a pedal/transmitter pair have been linked, they
should not need to be linked again.
Wireless Setup
Turn on the pedal and transmitter. Connect the
output jack of the Pedal into an amplifier,
preamp, effects pedal, mixer, or other
appropriate equipment. Plug the transmitter
into the instrument. Turn the volume on the
instrument to its maximum level for best
results. Step on the pedal’s footswitch once to
mute the output and enable the tuner display.
Step on the pedal’s footswitch again to un-
mute the output and disable the tuner display.
Wired Setup
Turn on the pedal. Connect the output jack of
the pedal to an amplifier, effects pedal, mixer,
or other appropriate audio equipment.
Connect an instrument to the input jack of the
pedal. Step on the pedal’s footswitch once to
mute the output and enable the tuner display.
Step on the pedal’s footswitch again to un-
mute the output and disable the tuner display.
Tuning Tips
- Turn instrument volume to the max level.
- Pluck single string with fingertip, not a pick.
- Mute strings that are not being tuned.
Transmitter LED Indication
- One flash every 2 seconds = Normal Use.
- Two flashes every 2 seconds = No Link.
- Solid yellow = Low Battery.
Specifications
Frequency: 2.404GHz – 2.476GHz
RF Transmit Power: 3.5dBm
Transmitter Battery: AAA Alkaline Battery(1)
Receiver Battery: 9V Alkaline Battery(1)
DC Power Connection: 8-12V DC 100mA
(Center Ground, Case Positive)
For Best Results
- Do not use in areas with excessive WiFi
(IEEE 802.3) network access points.
- Turn the instrument volume up.
- Use new batteries for performance.
Limited Lifetime Warranty
For warranty details contact:
OnBoard Research Corporation
1321 Valwood Parkway, STE 440
Carrollton, TX, 75006
Email: Support@tuners.com
Web:
mute the output and disable the tuner display.
Tuning Tips
- Turn instrument volume to the max level.
- Pluck single string with fingertip, not a pick.
- Mute strings that are not being tuned.
Transmitter LED Indication
- One flash every 2 seconds = Normal Use.
- Two flashes every 2 seconds = No Link.
- Solid yellow = Low Battery.
Specifications
Frequency: 2.404GHz – 2.476GHz
RF Transmit Power: 3.5dBm
Transmitter Battery: AAA Alkaline Battery(1)
Receiver Battery: 9V Alkaline Battery(1)
DC Power Connection: 8-12V DC 100mA
(Center Ground, Case Positive)
For Best Results
- Do not use in areas with excessive WiFi
(IEEE 802.3) network access points.
- Turn the instrument volume up.
- Use new batteries for performance.
Limited Lifetime Warranty
For warranty details contact:
OnBoard Research Corporation
1321 Valwood Parkway, STE 440
Carrollton, TX, 75006
Email: Support@tuners.com
Web:
www.tuners.com
Phone: 1 (800) 340-8890
SET/
LINK
ADJ
PWR
9V DC
LINK
PWR
Pedal Rear Panel Diagram:
Transmitter Diagram: