Taiwan Biotronic Technology Inc. 48525332323030 Manuel D’Utilisation

Heart Rate Transmitter

Elastic Strap

O-Ring

Battery Cover

Screw x 4pcs

Magnetic Key

3V CR2032
Lithium Battery

This Transmitter includes a 3V CR2032 lithium battery.
Please follow below steps to install the battery.
Step 1.
Insert the battery (CR2032) with the positive (+) side up.

☆

Step 2.
Put on the O-Ring in the groove to ensure water resistance.

☆

    composition from being spoiled by sweat and moisture.
Step 3.
Place Battery Cover with convex face up.
Step 4.
Tighten 4 screws properly.

Thank you for purchasing LifeVisa products.  This manual contains
information required to use the Heart Rate Transmitter.  Please read this
manual thoroughly before you use the Heart Rate Transmitter.

1

3. Adjust the strap length to fit around your chest
    

snugly and comfortably, just below the pectoral

    

muscles.

●

 If you are not getting a good connection to the host, please

(a) Check the Transmitter and make sure it's not worn too high or too low
      on the chest.  Adjust the position of the Transmitter on the chest to
      see if satisfactory connection has been achieved.
(b) Apply some ECG gel on the electrodes to get better performance.
(c) Check if the battery is installed properly or change a new battery.
(d) Repeat HOST CONNECTION section.

●

 The Transmitter will not detect heart rate when operated under water.

●

 The effective range of the whole system is 10 meters.  If the host is

   away by a greater distance than this, it might not receive a heart rate
   signal.

Care of the Heart Rate Transmitter
●

 After every use, you should clean the electrodes in warm fresh water

   and  dry with a dry cloth.
●

 DO NOT store the Transmitter wet; it must be stored in a cool and dry

   place, and kept out of extremely cold and hot.
●

 The Transmitter should be stored flat rather than folded and should

   never be bent or stretched, as this may damage the electrodes.
●

 Never lay the Transmitter on a metal surface or near magnet.

●

 Avoid the Transmitter from direct exposure to sunlight.

●

 Electrodes and gel should never be applied over broken skin.

●

 Trim (don't shave) your body hair where electrodes are going to be put.

●

 Clean skin before and after wearing the Transmitter.

4. Check that the wet electrode areas are
    firmly against your skin and that the logo
    of the Transmitter is in a central, upright
    position.

4

3. Wait for connection.

4. The host should begin to display a reading, showing the connection
    has been done and you can start your workouts.

☆

☆

The Heart Rate Transmitter consists of two conductive electrodes.  The
electrodes sense the heart beat.

1. For best performance, before wearing the Transmitter, please moisten
    the electrodes on the back of the Transmitter using clean tap water or
    ECG gel.  This makes it easier for the electrodes to detect the electrical
    signal.

2. Attach one side of the strap to the Transmitter.  Then wear it over your
    chest and meet the strap with the Transmitter at the other side.

ELECTRODES

3

Step 1.

Step 2.

Step 3.

Step 4.

2

☆

This Transmitter must be recognized to the host before being used for the first
time.  Please follow below instructions to complete the connection.

1. Turn on the host and enter connection
    mode.  The host will wait the signal
    for 1 minute.  If not receiving the
    signal, the host will exist the
    connection mode automatically.

2. Use Magnetic Key to startup the
    host connection function in the
    Heart Rate Transmitter by sliding
    on the top of Transmitter.

☆

☆

atteries 

disposed of in compliance with applicable

laws and regulations

Connection

done!!!