Peerless-AV ADS100-A252 Manuel D’Utilisation
9 of 12
ISSUED: 10-07-13 SHEET #: 180-9052-1
Transmitter and Amplifi er Pairing
The following presumes at least 1 amplifi er is already paired with the transmitter.
Step 1
Apply power to the ADS100-T8 transmitter by pressing the power button on the front left. The two
right side front face LED’s will illuminate red. The audio source(s) also should be present and on,
and connected to inputs 1-4 at least. A portable music player with rca outputs can be used also for
channel assignment.
Apply power to the ADS100-T8 transmitter by pressing the power button on the front left. The two
right side front face LED’s will illuminate red. The audio source(s) also should be present and on,
and connected to inputs 1-4 at least. A portable music player with rca outputs can be used also for
channel assignment.
Step 2
Apply power to the amplifi er(s) installed. Also ensure the speakers are connected, or at least a single
speaker. Both blue LED’s will blink about every second.
Apply power to the amplifi er(s) installed. Also ensure the speakers are connected, or at least a single
speaker. Both blue LED’s will blink about every second.
Step 3
At the transmitter face, depress the "SYNC 1-4" button once. The face LED and TX LED will both
blink allowing 2 minutes to sync the appropriate amplifi er. This allows any and all 4 inputs matched
to that TX module to be synced. If not synced, resumes previous assignment. The process can start
again.
At the transmitter face, depress the "SYNC 1-4" button once. The face LED and TX LED will both
blink allowing 2 minutes to sync the appropriate amplifi er. This allows any and all 4 inputs matched
to that TX module to be synced. If not synced, resumes previous assignment. The process can start
again.
Step 4
At the amplifi er, press “Sync” button once. The blue LED wills top blinking indicating it has locked onto
the TX module. If not on the input channel desired, press the “CH-SEL” button to scroll through the
inputs to fi nd the correct one(s). LED on transmitter face and TX module will illuminate solid blue to
indicate successful pairing.
At the amplifi er, press “Sync” button once. The blue LED wills top blinking indicating it has locked onto
the TX module. If not on the input channel desired, press the “CH-SEL” button to scroll through the
inputs to fi nd the correct one(s). LED on transmitter face and TX module will illuminate solid blue to
indicate successful pairing.
Step 5
Repeat the above procedure for additional amplifi ers. Each amplifi er needs to be synced from start to
fi nish as above. Return to the amplifi er to fi nish the installation.
Repeat the above procedure for additional amplifi ers. Each amplifi er needs to be synced from start to
fi nish as above. Return to the amplifi er to fi nish the installation.
Returning To Finish The Installation
Step 1
Install the Drywall Clamps onto each side of the amplifi er using the center slot.
Install the Drywall Clamps onto each side of the amplifi er using the center slot.
Step 2
Feed the amplifi er though the wall cut out, using the oval cutouts on the holding bracket with your
fi ngers. Guide the amp in and toward the wiring fi rst, then back up so the top of the holding bracket is
outside of the wall, then pull out slightly and drop down onto cut out bottom edge. The holding bracket
should be outside but fl ush to the drywall surface.
Feed the amplifi er though the wall cut out, using the oval cutouts on the holding bracket with your
fi ngers. Guide the amp in and toward the wiring fi rst, then back up so the top of the holding bracket is
outside of the wall, then pull out slightly and drop down onto cut out bottom edge. The holding bracket
should be outside but fl ush to the drywall surface.
Step 3
Snug clamp screws to secure the amp.
Snug clamp screws to secure the amp.
Step 4
Attach 2 gang cover plate to amplifi er holding bracket.
Attach 2 gang cover plate to amplifi er holding bracket.