Vital Home Systems LLC 1050 Manuel D’Utilisation
P a g e
| 6
© 2015 Vital Home Systems
Operation
IMPORTANT NOTICE TO USER: The installation of
any water detection or automatic water shut off
system does NOT guarantee water will be detected
on all occasions or circumstances. Due to the
variety of environments the system can be
installed, how it is maintained and types of
installation, Vital Home Systems does NOT
guarantee or warrant against water or property
damage as a result of or/with the use of this
system.
any water detection or automatic water shut off
system does NOT guarantee water will be detected
on all occasions or circumstances. Due to the
variety of environments the system can be
installed, how it is maintained and types of
installation, Vital Home Systems does NOT
guarantee or warrant against water or property
damage as a result of or/with the use of this
system.
Upon receiving the signal from the Water Sensors or
VC100, the VHS-1050 will flash the Dialer LED and
play the appropriate message for specific event and
time period.
VC100, the VHS-1050 will flash the Dialer LED and
play the appropriate message for specific event and
time period.
NOTE:
For VC-100 / 4LWS, it will play appropriate
voice message locally for 15 seconds before
dialing out.
dialing out.
If two or more sensors are triggered one
after another, the corresponding messages
will be played in rotation.
will be played in rotation.
After dialing a phone, and the line is not
engaged, the Dialer LED will flash ON and
the Dialer will automatically play the
appropriate message on a remote phone to
summon help.
the Dialer will automatically play the
appropriate message on a remote phone to
summon help.
If no telephone number is stored, the Dialer
will not dial to report.
When two or more telephone numbers are
stored, the Dialer will dial in accordance to
the Priority Order number. If the number
being dialed cannot connect, it will try the
next number.
the Priority Order number. If the number
being dialed cannot connect, it will try the
next number.
Each phone number will be tried in
rotation, with the Dialer making a maximum
of 10 calls in total.
of 10 calls in total.
When the recipient answers the phone, the
voice message will play, this must be
acknowledged by pressing “9” in order for
the VHS-1050 to stop dialing and go back on
hook.
acknowledged by pressing “9” in order for
the VHS-1050 to stop dialing and go back on
hook.
If VHS-1050 does not receive the
acknowledgement from receiver within 60
seconds, it will automatically go back on
hook. After five seconds, it will again start
the dialing.
seconds, it will automatically go back on
hook. After five seconds, it will again start
the dialing.
When a total of 10 calls have been made to
the stored telephone numbers without any
acknowledgement, the Dialer returns to
Normal Mode. The Dialer LED will continue
to flash to remind the user of the reporting
failure.
acknowledgement, the Dialer returns to
Normal Mode. The Dialer LED will continue
to flash to remind the user of the reporting
failure.
During dialing, if the Dialer receives a
disarm signal from the Dialer (when its
“ACK” key is pressed) the Dialer LED goes
OFF and the Dialer stops the reporting.
“ACK” key is pressed) the Dialer LED goes
OFF and the Dialer stops the reporting.
The 1050 phone numbers entered are to be
for cell phone numbers only that way if a
line is busy when called it will leave a voice
mail.
line is busy when called it will leave a voice
mail.
Fault Situations
The Orange LED (Fault LED) will flash ON if the VHS-
1050 or any of the Learned devices are out-of-order
or in low-battery status.
1050 or any of the Learned devices are out-of-order
or in low-battery status.
When there is Fault situation indicated by
Orange LED ON, the VHS-1050 Dial out to
the numbers in the phonebook in order of
priority with Sensor/Valve name with a
“Low Battery” or “Fault Detected”.
the numbers in the phonebook in order of
priority with Sensor/Valve name with a
“Low Battery” or “Fault Detected”.
When there is Fault situation indicated by
Orange LED ON, pressing “ACK” will play the
corresponding voice message for 30
seconds or till CLR is pressed.
corresponding voice message for 30
seconds or till CLR is pressed.
When there is no Fault, pressing “ACK” will
produce no response.
The Orange LED will turn OFF automatically
once all of the faulty conditions are
restored, or faulty devices are removed via
the software.
restored, or faulty devices are removed via
the software.
Supervision Fault
VC-100 will send “I’m Here” signal to the VHS-
1050 every 24~30 hours. If the VHS-1050 has
not received the signal for seven (7) days, it
will cause Out-of-Order fault condition.
not received the signal for seven (7) days, it
will cause Out-of-Order fault condition.
WATER SENSOR will send “I’m Here” signal to
VHS-1050 every four hours; if the VHS-1050
has not received the supervision signal for 12
hours, it will cause an Out-of-Order fault
condition.
has not received the supervision signal for 12
hours, it will cause an Out-of-Order fault
condition.