SensingTek Co. Ltd. SDZ2100 Manuel D’Utilisation
replaceable materials shall not be liable for, and customers using the
products, their other tangible or intangible loss arising, nor take any
responsibility.
products, their other tangible or intangible loss arising, nor take any
responsibility.
6、Installation steps (recommended by a professional
technician)
technician)
(1) Draw a 15 cm long at the ready to install the horizontal line
(2) Unscrew counterclockwise Smoke fixed base
(3) Fixed two large holes align horizontal line marks the position of the
(2) Unscrew counterclockwise Smoke fixed base
(3) Fixed two large holes align horizontal line marks the position of the
screws
(4) Using an electric drill (5mm bits) to drill a hole and buried in two
plastic nails (Gecko)
(5) Lock the screws to fix the base
(6) Align the Smoke installation well fixed base, yield to clockwise,
(6) Align the Smoke installation well fixed base, yield to clockwise,
combined with the Smoke as a whole. Try to Smoke in order to make
sure it is installed properly.
sure it is installed properly.
7、Smoke Specification
Induction type: photoelectric detection of smoke
Smoke detection sensitivity: UL217 (factory default)
Power supply: 1.5V two AA alkaline batteries (normal standby mode, uses about 18
months)
months)
Built-in alarm sound mode: UL
Working temperature:-40 ° c ~85 ° c
Operating humidity: 0~95%
Interface: IEEE802.15.4
Frequency Range: 2.4-2.483GHz
Transmission Speed: 250Kbps
Transmission Power: 18dBm (Default)
Transmission Range: 150M(Line of Sight)
Sensitivity: -95dBm
Size:114mm*114mm*63mm
Working temperature:-40 ° c ~85 ° c
Operating humidity: 0~95%
Interface: IEEE802.15.4
Frequency Range: 2.4-2.483GHz
Transmission Speed: 250Kbps
Transmission Power: 18dBm (Default)
Transmission Range: 150M(Line of Sight)
Sensitivity: -95dBm
Size:114mm*114mm*63mm
8、Zigbee reset connecting Gateway:
Pairing has to be replaced, you will need to open the body back
panel base, locate the battery place the top button, and continue to
press the button for three seconds, the product will enter the pairing
search and automatic pairing mode, this pairing is a Gateway
connecting the power for two minutes before they can match。
press the button for three seconds, the product will enter the pairing
search and automatic pairing mode, this pairing is a Gateway
connecting the power for two minutes before they can match。
This device is Fixed installation, so the minimum distance from
body is 20cm
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help.