Transition Networks E-100BTX-FX-05 Manuel D’Utilisation
2
E-100BTX-FX-05
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
The media converters with the “HT” extension in the part number can be used in
an extended temperature environment from -25°C to 65°C (-13°F to 149°F).
an extended temperature environment from -25°C to 65°C (-13°F to 149°F).
Part Number
Description
SPS-1872-SA
Optional External Power Supply; 18-72VDC Stand-Alone Wide-
Input; Output: 12.6VDC, 1.0 A
Input; Output: 12.6VDC, 1.0 A
SPS-1872-CC
Optional External Power Supply; 18-72VDC Piggy-Back Wide-
Input; Output: 12.6VDC, 1.0 A
Input; Output: 12.6VDC, 1.0 A
E-MCR-04
12-Slot Media Converter Rack (includes universal internal power
supply) 17 x 15 x 5 in. (432 x 381 x 127 mm)
supply) 17 x 15 x 5 in. (432 x 381 x 127 mm)
WMBL
Optional Wall Mount Brackets; 4.0 in. (102 mm)
WMBV
Optional Vertical Mount Bracket; 5.0 in. (127 mm)
WMBD
Optional DIN Rail Mount Bracket; 5.0 in. (127 mm)
WMBD-FS
Optional DIN Rail Mount Bracket (flat, small); 3.1in. (79 mm)
Part Number
Port One - Copper
100Base-TX
100Base-TX
Port Two - Duplex Fiber-Optic
100Base-FX
100Base-FX
E-100BTX-FX-05(HT)
RJ-45
100 m (328 ft)*
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
2 km (1.2 miles)*
E-100BTX-FX-05(SCHT)
RJ-45
100 m (328 ft)*
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
2 km (1.2 miles)*
E-100BTX-FX-05(SMHT)
RJ-45
100 m (328 ft)*
100 m (328 ft)*
SC, 1310 nm single mode
20 km (12.4 miles)*
20 km (12.4 miles)*
E-100BTX-FX-05(LHHT)
RJ-45
100 m (328 ft)*
100 m (328 ft)*
SC, 1310 nm single mode
40 km (24.9 miles)*
40 km (24.9 miles)*
E-100BTX-FX-05(XLHT)
RJ-45
100 m (328 ft)*
100 m (328 ft)*
SC, 1310 nm single mode
60 km (37.3 miles)*
60 km (37.3 miles)*
E-100BTX-FX-05(LWHT)
RJ-45
100 m (328 ft)*
100 m (328 ft)*
SC, 1550 nm single mode
80 km (49.7 miles)*
80 km (49.7 miles)*
E-100BTX-FX-05(100HT)**
RJ-45
100 m (328 ft)*
100 m (328 ft)*
SC, 1310Tx/1550Rx nm single
mode
20 km (12.4 miles)*
mode
20 km (12.4 miles)*
E-100BTX-FX-05(101HT)**
RJ-45
100 m (328 ft)*
100 m (328 ft)*
SC, 1550Tx/1310Rx nm single
mode
20 km (12.4 miles)*
mode
20 km (12.4 miles)*
Accessories sold separately
**E-100BTX-FX-05(100/101HT) are installed in pairs.
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the 4-position switch and jumper. Failure to observe
this caution could result in damage or failure of the media converter.
precautions when setting the 4-position switch and jumper. Failure to observe
this caution could result in damage or failure of the media converter.
4-position switch
• The 4-position switch is
located on the side of the
media converter. Use a
small flat-blade screwdriver
or a similar device to set
the recessed switches.
media converter. Use a
small flat-blade screwdriver
or a similar device to set
the recessed switches.
1. Auto-Negotiation
up
Enables Auto-Negotiation for the copper connection.
down
Disables Auto-Negotiation for the copper connection.
2. Pause Control
up
Enabled
down
Disabled
3. Link Pass-Through
up
Enabled
down
Disabled
4. Far-End Fault
up
Enabled
down
Disabled
AutoCross™ Jumper
The AutoCross feature allows either straight-through (MDI) or crossover
(MDI-X) cables to be used when connecting to devices such as hubs,
transceivers, or network interface cards (NICs). AutoCross determines the
characteristics of the cable connection and automatically configures the unit
to link up, regardless of the cable configuration.
(MDI-X) cables to be used when connecting to devices such as hubs,
transceivers, or network interface cards (NICs). AutoCross determines the
characteristics of the cable connection and automatically configures the unit
to link up, regardless of the cable configuration.
NOTE: AutoCross is enabled by default, the recommended state.
The jumper is located on the media converter’s circuit board To set the
jumper:
jumper:
1.
Using a small screwdriver, remove the four (4) screws that secure the
cover; then remove the cover from the media
converter.
cover; then remove the cover from the media
converter.
2.
Locate header J3 on the circuit board; using a small
needle-nosed pliers move the jumper to the desired
position. (Refer to the drawing to the right.)
needle-nosed pliers move the jumper to the desired
position. (Refer to the drawing to the right.)
3.
Carefully replace the cover, and then replace the
four (4) screws to secure the cover to the media
converter.
four (4) screws to secure the cover to the media
converter.
J3
Enabled AutoCross
J3
Disabled AutoCross
Link Pass-Through (up=Enable)
Pause (up=Enable)
Auto-Negotiation (up=Enable)
Far End Fault
(up=Enable)
(up=Enable)
1 2 3 4