Справочник Пользователя для Transition Networks E-100BTX-FX-05

2

E-100BTX-FX-05

24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 

The media converters with the “HT” extension in the part number can be used in
an extended temperature environment from -25°C to 65°C (-13°F to 149°F).

SPS-1872-SA

Optional External Power Supply; 18-72VDC Stand-Alone Wide-
Input; Output:  12.6VDC, 1.0 A 

SPS-1872-CC

Optional External Power Supply; 18-72VDC Piggy-Back Wide-
Input; Output:  12.6VDC, 1.0 A 

E-MCR-04

12-Slot Media Converter Rack (includes universal internal power
supply) 17 x 15 x 5 in. (432 x 381 x 127 mm)

WMBL

Optional Wall Mount Brackets; 4.0 in. (102 mm)

WMBV

Optional Vertical Mount Bracket; 5.0 in. (127 mm)

WMBD

Optional DIN Rail Mount Bracket; 5.0 in. (127 mm)

WMBD-FS

Optional DIN Rail Mount Bracket (flat, small); 3.1in. (79 mm)

E-100BTX-FX-05(HT)

RJ-45 
100 m (328 ft)*

ST, 1300 nm multimode
2 km (1.2 miles)*

E-100BTX-FX-05(SCHT)

RJ-45 
100 m (328 ft)*

SC, 1300 nm multimode
2 km (1.2 miles)*

E-100BTX-FX-05(SMHT)

RJ-45 
100 m (328 ft)*

SC, 1310 nm single mode
20 km (12.4 miles)*

E-100BTX-FX-05(LHHT)

RJ-45 
100 m (328 ft)*

SC, 1310 nm single mode
40 km (24.9 miles)*

E-100BTX-FX-05(XLHT)

RJ-45 
100 m (328 ft)*

SC, 1310 nm single mode
60 km (37.3 miles)*

E-100BTX-FX-05(LWHT)

RJ-45 
100 m (328 ft)*

SC, 1550 nm single mode
80 km (49.7 miles)*

E-100BTX-FX-05(100HT)**

RJ-45 
100 m (328 ft)*

SC, 1310Tx/1550Rx nm single
mode 
20 km (12.4 miles)*

E-100BTX-FX-05(101HT)**

RJ-45 
100 m (328 ft)*

SC, 1550Tx/1310Rx nm single
mode 
20 km (12.4 miles)*

**E-100BTX-FX-05(100/101HT) are installed in pairs.

techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.

3

CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the 4-position switch and jumper. Failure to observe
this caution could result in damage or failure of the media converter.

• The 4-position switch is

located on the side of the
media converter. Use a
small flat-blade screwdriver
or a similar device to set
the recessed switches.   

1.  Auto-Negotiation 

up

Enables Auto-Negotiation for the copper connection.

down

Disables Auto-Negotiation for the copper connection.

2.  Pause Control 

up

Enabled

down

Disabled

3.  Link Pass-Through

up

Enabled

down

Disabled

4.  Far-End Fault

up

Enabled

down

Disabled

The AutoCross feature allows either straight-through (MDI) or crossover
(MDI-X) cables to be used when connecting to devices such as hubs,
transceivers, or network interface cards (NICs). AutoCross determines the
characteristics of the cable connection and automatically configures the unit
to link up, regardless of the cable configuration. 

NOTE: AutoCross is enabled by default, the recommended state. 

The jumper is located on the media converter’s circuit board  To set the
jumper:

1.

Using a small screwdriver, remove the four (4) screws that secure the
cover; then remove the cover from the media
converter.

2.

Locate header J3 on the circuit board; using a small
needle-nosed pliers move the jumper to the desired
position. (Refer to the drawing to the right.)

3.

Carefully replace the cover, and then replace the
four (4) screws to secure the cover to the media
converter.

J3

Enabled AutoCross

J3

Disabled AutoCross

Link Pass-Through (up=Enable)

Pause (up=Enable)

Auto-Negotiation (up=Enable)

Far End Fault
(up=Enable)

1 2 3 4