Viessmann 4557 Fiche De Données
![Viessmann](https://files.manualsbrain.com/attachments/6b7cc977d98c2279c4f2e5a6b0fc670f108e98bb/common/fit/150/50/5498f61aefbb2ea8485500a721c49346ff196fa8a95b10cef11f7ca18119/brand_logo.png)
10
rot /
red
grün /
green
Mot. / DCC
4557
gelb
braun
Digitalzentrale
braun
/ yellow
brown
Digital Command Station
brown
Fig. 6
Abb. 6
Fig. 6.1
Abb. 6.1
rot /
red
grün /
green
DCC
4557
rot
braun
Digital-
zentrale
braun
gelb
/ red
brown
Digital
Command
Station
brown
yellow
rot /
red
grün /
green
MM
4557
rot
braun
braun
gelb
Digital-
zentrale
/ red
brown
brown
yellow
Digital
Command
Station
Digitalbetrieb auf einer Lokadresse
Um den Decoder auf eine Lokadresse zu programmieren,
gehen Sie wie folgt vor:
Bestimmen Sie, welches Digitalsystem verwendet wer-
Bestimmen Sie, welches Digitalsystem verwendet wer-
den soll. Gehen Sie dazu vor, wie unter den Punkten 1
bis 4 bei „Einrichtung mit DCC-Zentralen“ oder „Einrich-
tung mit Motorola-Zentralen“ beschrieben. Stellen Sie alle
Lokomotiven auf Fahrstufe Null, sofern Ihre Zentrale dies
nicht automatisch tut.
An Punkt 5 senden Sie jedoch keinen Weichenschalt-
An Punkt 5 senden Sie jedoch keinen Weichenschalt-
befehl, sondern einen Lok-Fahrbefehl auf der Adresse,
die der Antrieb bekommen soll. Betätigen Sie dazu den
Fahrregler, so dass eine Fahrstufe an die Adresse gesen-
det wird, die nicht Null ist. Diese Adresse entspricht der
Gruppenadresse eines typischen 4-fach-Decoders. Auf
dieser Lokadresse wählen Sie dann eine Funktion F1 bis
F4, die dadurch dem Weichenantrieb zugeordnet wird.
Somit können Sie 4 Weichenantriebe auf eine Lokadres-
se legen, analog zum 4-fach-Decoder. Der Adressbereich
ist auf 1 bis 99 begrenzt.
Digital mode with a locomotive address
Proceed as follows if you wish to programm the decoder
to a locomotive address.
Decide which digital system you are going to use. Pro-
Decide which digital system you are going to use. Pro-
ceed as described in points 1 through 4 in the chapter
“Configurations with DCC command stations” or “Con-
figuration with Motorola central units”. Set all locomtives
to speed step 0 if your command station does not do that
automatically.
Instead of the accessory command as per point 5 send
Instead of the accessory command as per point 5 send
a locomotive driving command to the address to be as-
signed to this drive. Turn up the throttle in order to send
a speed command greater than 0. This address corre-
sponds with the typical group address of an accessory de-
coder with four double-outputs. Select one of the functions
F1 through F4 of this locomotive address, which assigns
the functions of this address to the turnout drive. Thus you
may control four turnouts with one locomotive address
similar to a decoder for four accessories. The address
range is limited to addresses from 1 through 99.
Anschluss nach Adressprogrammierung für invertierte Stellrichtung!
Connection after programming the address - use for reverse switching direction!