Hirschmann DVB-T antenna HIRSCH Fiche De Données
Codes de produits
HIRSCH
6
– Voltage supply: The supply voltage is
electrically isolated from the housing.
– Ground connection: The SPIDER is
grounded via a pin of the 3pin terminal
block.
block.
Fig. 3: Pin configuration of 3pin terminal
block
2. Configuration
2.1 CONNECTING DTE AND OTHER
NETWORK SEGMENTS
It is possible to connect with
– SPIDER 3TX-TAP up to three
– SPIDER 5TX, SPIDER 5TX EEC up to five
– SPIDER 8TX, SPIDER 8TX EEC up to eight
– SPIDER 1TX/1FX... up to one
– SPIDER 4TX/1FX... up to four
data terminal equipments (DTE) or other
network segments to the 10/100 Mbit/s
ports using twisted pair cabling (ref. Fig. 4).
NETWORK SEGMENTS
It is possible to connect with
– SPIDER 3TX-TAP up to three
– SPIDER 5TX, SPIDER 5TX EEC up to five
– SPIDER 8TX, SPIDER 8TX EEC up to eight
– SPIDER 1TX/1FX... up to one
– SPIDER 4TX/1FX... up to four
data terminal equipments (DTE) or other
network segments to the 10/100 Mbit/s
ports using twisted pair cabling (ref. Fig. 4).
One further data terminal equipment or
optical network component can be connec-
ted at 100 Mbit/s to the optical port of the
– SPIDER 1TX/1FX...
– SPIDER 4TX/1FX...
using fiber optic cable.
optical network component can be connec-
ted at 100 Mbit/s to the optical port of the
– SPIDER 1TX/1FX...
– SPIDER 4TX/1FX...
using fiber optic cable.
3. Assembly, startup procedure
and dismantling
3.1 UNPACKING, CHECKING
䡺 Check whether the package was deliver-
ed complete (see scope of delivery).
ed complete (see scope of delivery).
䡺 Check the individual parts for transport
damage.
damage.
z
Warning!
Use only undamaged parts!
Use only undamaged parts!
3.2 ASSEMBLY
The equipment is delivered in a ready-to-
operate condition. The following procedure
is appropriate for assembly:
The equipment is delivered in a ready-to-
operate condition. The following procedure
is appropriate for assembly:
+24 V
0 V
䡺 Pull the terminal block off the SPIDER
and wire up the supply voltage lines.
and wire up the supply voltage lines.
䡺 Fit the SPIDER on a 35 mm standard bar
to DIN EN 50 022.
to DIN EN 50 022.
䡺 Attach the upper snap-on slide bar of
the SPIDER to the standard bar and press it
down until it locks in position.
the SPIDER to the standard bar and press it
down until it locks in position.
䡺 Fit the signal lines.
Notes:
– The SPIDER is grounded via a pin of the
Notes:
– The SPIDER is grounded via a pin of the
terminal block.
– Do not open the housing.
– The shielding ground of the twisted pair
lines which can be connected is electrical-
ly connected to the ground connection.
ly connected to the ground connection.
Fig. 5: Assembling the SPIDER
Fig. 6: Dimensions
13,7
70
63,3
23
8,5
3.3 STARTUP PROCEDURE
䡺 You start up the SPIDER by connecting
the supply voltage via the 3-pin terminal
block.
the supply voltage via the 3-pin terminal
block.
3.4 DISMANTLING
䡺 To take the SPIDER off the ISO/DIN rail,
unlock the snap-in mechanism according to
Fig 7.
unlock the snap-in mechanism according to
Fig 7.
Fig. 7: Dismantling the SPIDER
4. Further support
In the event of technical queries, please talk
to the Hirschmann contract partner respon-
sible for looking after your account or
directly to the Hirschmann office. You can
find the addresses of our contract partners
– on the Internet
to the Hirschmann contract partner respon-
sible for looking after your account or
directly to the Hirschmann office. You can
find the addresses of our contract partners
– on the Internet
http://www.hirschmann-ac.com
Our support line is also at your disposal:
Tel. +49(1805) 14-1538
Fax +49(7127) 14-1551
Tel. +49(1805) 14-1538
Fax +49(7127) 14-1551
Answers to Frequently Asked Questions can
be found on the Hirschmann product site
be found on the Hirschmann product site
http://www.hirschmann-ac.com
The FAQs are located under „Service“ in
the Automation and Network Solutions
section.
www.hicomcenter.com gives you an up-to-
date overview of training courses about
technology and products.
The FAQs are located under „Service“ in
the Automation and Network Solutions
section.
www.hicomcenter.com gives you an up-to-
date overview of training courses about
technology and products.
MICE
SPIDER
Fig. 4: Configuration with SPIDER: Connection of (depending on product type):
– up to 8 data terminal equipments or further segments via TP
– and up to 1 data terminal equipment or further segment via F/O
– and up to 1 data terminal equipment or further segment via F/O