C&E LED wall light Warm white LSWL1661 Silver-grey LSWL1661 Fiche De Données

  

   These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,  

D-92240 Hirschau (www.conrad.com). 

 

 All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, 
or the capture in electronic data processing systems require the prior written approval by the editor. 
Reprinting, also in part, is prohibited. 

 

 These operating instructions represent the technical status at the time of printing. Changes in         
technology and equipment reserved. 

 

 

Pay attention to the information in the chapter “Preparations for Installation”!

•   Remove the mounting plate from the rear of the wall light. For this purpose, fully unscrew the 

two screws to the left and right on the wall light.

•   Mark the positions for installation on the wall, through the holes of the mounting plate.
•   Push the mains cable through the appropriate cable bushing in the mounting plate and attach 

the mounting plate to the wall using suitable screws and wall plugs, if necessary.

 

 When drilling mounting holes or screwing into place, ensure that no existing cables 
or pipes are damaged.

•   Connect the mains cable using the terminal strip in the wall light’s housing (brown cable = L, 

blue cable = N, green/yellow cable = PE/earth, earth symbol). 

 

The protective earth wire must be connected! 

 

 If the wall lamp replaces an existing lamp and there is not a protective earth wire 
available, the lamp must not be installed. First, draw a new mains cable.

 

 In the case where no protective earth conductor is connected, faulty functioning of 
the mains voltage might charge the metal housing of the wall lamp. There is a life-
threatening hazard through an electric shock!

 

 Make sure only the minimum required length of the cable is stripped; otherwise it 
could cause a short-circuit.

 

 Also check the other screwing connections at the terminal strip (for the connection 
cables of the light) and fasten them, if necessary. 

•   Place the wall lamp on the mounting plate. Depending on the desired use and purpose, the 

LED in the wall light can face upwards to the ceiling or downwards, to the fl oor.

   Make sure that the mains cables or the cables of the light itself are not pinched or trapped.
•   Re-insert the two screws that you removed at the beginning, so the LED wall light is secured 

to the mounting plate.

•  Switch on the mains voltage again and make sure that the wall light is functioning.

   If the bulbs in the wall light do not light, switch off the mains voltage immediately 

(take out the fuse or switch off automatic cut-out, switch off corresponding ground 
fault circuit interrupter).

 

Thereafter, check the connections of the wall lamp.

 

In case of doubt, contact a professional (e.g. an electrician)!

•   The wall lamp does not require maintenance. The LED used is very long-lasting and it cannot 

be replaced.

•   Switch off the wall light or disconnect it from the mains before cleaning. After that, allow suf-

fi cient time for the wall light to cool down.

•   The exterior of the wall lamp should only be wiped with a clean, soft, dry cloth. Do not use ag-

gressive cleaning agents or chemical solutions that could damage the housing (discolouring) 
or impair operation. 

  Do not press too hard on the housing, as scratches might appear.
   Dust can easily be removed using a clean, soft brush and a vacuum cleaner.

   Dispose of an unserviceable product in accordance with the relevant statutory 

regulations.

Operating voltage .........................220 - 240 V/AC, 50/60 Hz
Power consumption ......................max. 7 W
LED type .......................................1 x 6.6 W 
Light colour ...................................3,000K (Warm white)
Light fl ux .......................................355 lm
Angle of radiation ..........................approx. 150°
Protection class ............................I
Installation location .......................Only in dry enclosed indoor spaces
Dimensions (H x W x D) ...............100 x 180 x 65 mm
Weight ..........................................approx. 720 g