Tascam DR-1 Manuel D’Utilisation
TASCAM DR-100MKII
21
3 – Preparation for Use
Using an AC adaptor (sold separately)
Connect the TASCAM PS-P520 AC adaptor (sold separately)
to the DC IN 5V connector as shown in the illustration.
to the DC IN 5V connector as shown in the illustration.
TASCAM
PS-P520
(Sold separately)
AC outlet
DC plug
CAUTION
Never use any adaptor other than the designated PS-
P520 AC adaptor. Use of a different adaptor could cause
malfunction, fire or electric shock.
P520 AC adaptor. Use of a different adaptor could cause
malfunction, fire or electric shock.
NOTE
Noise may occur when recording with a microphone if
•
the unit is too close to the AC adaptor. In such a case,
keep sufficient distance between the AC adaptor and
the unit.
The AC adaptor provides power when connected even if
keep sufficient distance between the AC adaptor and
the unit.
The AC adaptor provides power when connected even if
•
batteries are installed.
If installed, the lithium ion battery can also be recharged
If installed, the lithium ion battery can also be recharged
•
while the unit is used.
Using an external battery pack (sold
separately)
Connect a TASCAM BP-6AA external battery pack
(sold separately) to the DC IN 5V jack, as shown in the
illustration.
(sold separately) to the DC IN 5V jack, as shown in the
illustration.
TASCAM
BP-6AA
(Sold separately)
DC plug
CAUTION
Never use any external battery pack other than the
TASCAM BP-6AA. Use of a different battery pack could
cause malfunction, fire or electric shock.
TASCAM BP-6AA. Use of a different battery pack could
cause malfunction, fire or electric shock.
NOTE
If you connect a TASCAM BP-6AA external battery pack via
the included cord to this recorder while the recorder still
has batteries in it, power will be provided by the external
battery pack.
the included cord to this recorder while the recorder still
has batteries in it, power will be provided by the external
battery pack.
Preparing the remote control
Installing the battery
1 Remove the battery holder. While pressing 1, pull in
direction 2.
2 Install the coin-shaped lithium ion battery (CR2025)
into the holder with the correct +/– orientation.
3 Reinsert the battery holder into the remote control.
NOTE
At the time of purchase, this remote control comes with a
lithium coin battery (CR2025) installed. Before using the
remote control, pull the isolation sheet out of the battery
compartment.
lithium coin battery (CR2025) installed. Before using the
remote control, pull the isolation sheet out of the battery
compartment.
When to change the battery
Replace the battery with a new one when the range of the
remote control becomes short or if the function buttons
become unresponsive.
Use a coin-shaped lithium ion battery (CR2025).
remote control becomes short or if the function buttons
become unresponsive.
Use a coin-shaped lithium ion battery (CR2025).
Cautions about the use of the battery
Accidental swallowing of batteries by small children
is extremely dangerous. Keep batteries and remote
controls out of reach of small children. Consult a physician
immediately if a child should swallow a battery.
Misuse of a battery could cause it to leak, rupture or
otherwise be damaged. Please read and abide by the
following precautions when using batteries. (Also see
“Cautions about batteries” on page 4.)
is extremely dangerous. Keep batteries and remote
controls out of reach of small children. Consult a physician
immediately if a child should swallow a battery.
Misuse of a battery could cause it to leak, rupture or
otherwise be damaged. Please read and abide by the
following precautions when using batteries. (Also see
“Cautions about batteries” on page 4.)
Install the battery with the correct orientation.
•
Do not recharge the battery.
•
Do not heat or disassemble the battery or put it into fire
•
or water.